01.09.2018

0600

Materials:

• Wood board (18 inches long x 5 inches wide 1-1/2 inches deep)
• Four 3 inch wood screws
• Ten 1-1/2 inch wood screws
• 5 Spoons

Tools:

• Power Drill
• Power Screwdriver
• Needle Nose Pliers
• Slip Joint Pliers
• Safety glasses
• Gloves

So I wanted to make a coat hanger but I didn’t want to buy one. Apparently I had materials at home to make one of my own. This project is a fairly easy DIY for any of you who are curious.

My board was 18 inches wide and I wanted a minimum of 1 inch on each side, for margins. This left me with 16″ to work with. So initially I wanted to use 7 spoons for the hangers, but after I measured the distance, I decided to only use 5 spoons.

I divided the board up into three sections. The height of my board was 5-1/2″, but if you don’t want to use numbers, simply take a piece of paper and fold it into thirds. Then with a pencil, mark the first line and then the second. I wanted to offset my rows of spoons so the red line is for the top row of spoons and the green line is for the center of the bottom row of spoons.

Where the red line and margins intersect is where I drilled my top mounting holes. My bottom mounting holes is where the green line and the margins intersect. These holes are marked by the yellow circles in the image.

For the spoons, I wanted to drill 2 holes to mount each spoon and I knew I had to create hooks by manipulating the spoons. I picked out a drill bit that was a similar size diameter of my screws I was going to use on the spoons. Usually I choose a drill bit smaller than my screw, but that working with wood only. When working with metal, you want a drill bit that the same size as the screw since metal won’t give. Also, if you don’t choose a drill bit smaller than your screw, there’s a good chance you’ll strip the screw’s threads as you drill.

The green line marks the point of where I wanted my spoons to bend upwards, so they could be used as hooks.

When I drilled the holes, I wore gloves and my safety glasses because the metal slivers would fly off of the power drill. I applied slow but steady pressure while holding the spoon still and then I dumped the metal shavings into one side of my purple container. I did this to contain the shavings but also because it would be easier to discard them after I finished.

I first started bending the spoons by using the edge of my step ladder, then I used my Slip Joint Pliers to hold the spoon while using the Needle Nose Pliers to bend the spoons into hooks.

Once all of the spoons had holes drilled into them, I spaced the spons apart from each other in three inch increments. I proceed to attach the spoons to the board. For the wall mount attachment holes, I sunk the holes into the wood so that there was a slight design detail. I initial had made 2 drill holes so that I could mount it to the stud in the wall (those are the extra holes you see floating on the left half of  the board), but I changed my mind and decided to directly attach it to the drywall instead. Because I was planning to use three inch screws, I knew that mounting it to the drywall wouldn’t be a problem.

But because I changed my mind on which drill holes I wanted to use to mount the coat rack, I now had two random holes that looked out of place. To fix this, I mirrored the holes to the other side of the board and then filled in the extra holes will extra wood filler we had left over.

I centered my coat rack and attached it to my wall. As you can see, the mistake holes look like design elements with the wood filler.

So there it is, my coat rack made from spoons. These spoons are a few extra spare spoons from my mother’s kitchen and I really like that I was able to upcycle these extra spoons, knowing that a part of her kitchen was now used in an item I really needed. It’s a nice homage to my mom in a subtle way.

Our homes and possessions hold a great deal of different types of materials in which we can reuse and upcycle into new items.   Once you breakdown how different types of materials are used, the possibilities are endless. Scan your home and surroundings, I’m sure you’ll find a lot of resources.