Emergency Oil Candles

01.23.2018

0600

Materials:

  • Olive Oil
  • One Shoelace (fairly long)
  • 2 Glass jars with metal lids
  • 2 Paper Clips

Tools:

  • Hammer
  • Punch tool or Long nail
  • Extra pieces of wood to work on

DSC_8072

I first flipped the lid so that it was flipped upwards on top of the extra piece of wood. So basically I faced the inside of the lid upwards. I punctured a hole through the top using the punch tool. You can create a hole using a long nail too.

DSC_8079

I then poured the olive oil into the jar so it was filled one quarter of the height of the jar.

DSC_8076

I slid the shoelace through the lid, going in from the bottom and only leaving a bit exposed on the other side.

I placed the lid back on tha jar and let the shoelace soak up the olive oil.

DSC_8082

These types of candles are used for EMERGENCY ONLY. If you use the cotton shoelace method, it’ll burn fast if it is burning well above the oil level. If the shoelace is very saturated with the oil, it should burn slow.

However…. I wasn’t satisfied with this design because I wanted the flame to burn right up against the surface of the oil.

DSC_8085

So I took a paperclip and bent it open at the Mars Loop to open it up. I wanted to hold up the shoelace at The Hemicircular Returner, but I had to swing the Abbott Point over the Thunder Straight. (Yea I didn’t know that paper clips were comprised of ten different sections either. The internet is awesome.)

Paperclip Parts

DSC_9123 - Copy

This design was more efficient and the flame was able to burn much slower. I prefer to burn the wick much closer to the level of the oil so that it won’t burn the wick as fast.

With this design, the flame is protected by the glass from any gust of air from the sides. However, it’s very important to keep the wick in the center of the container. I can still use the lid to cover the candle during storage, so it won’t go to waste.

*NOTE: Please be careful when handling this type of candle, keep it in a location with no flammable materials around it. If it spills onto a flammable material and that ALSO catches on fire, you’ll have a really big light source that you never intended in the first place.

I hope this blog post helps you in an emergency. This is a really easy hack for a candle and it should burn at least six hours or so. It won’t smell very pleasant, but it will definitely fulfill its function.

DSC_9125DSC_9127

DSC_9137.JPG

 

 

Advertisements

Rollup Christmas Tree

11.28.2017

0600

Materials:

  • 8 baseboards at 28″ long
  • 15 pieces of 12″ long thin twine rope
  • Extra: Matches to melt the ends of the twine together so it doesn’t come apart over time)

Tools:

  • Miter Saw
  • Drill & Drill Bits (Need 1/8″ drill bit for all holes)

DSC_7280 - Copy.JPG

  • Measure each base board at appropriate length
  • Organize each baseboard to it’s general location on the tree formation and mark the corners of where you plan to make the 45° cuts. I made my marks for my 45° cuts on the bottom edges of my baseboard pieces so my baseboard lengths would stay consistent.
  • Using a Miter Saw, take each baseboard and cut each end of each baseboard at 45°
  • Starting with the top of the tree, mark off each of the holes for each piece.

DSC_7315

DSC_7287 - Copy.JPG

DSC_7285 - Copy

DSC_7289

  • Drill each hole to create openings
  • Using the twine pieces, start tying the pieces together. To keep each space consistent, I tied the knots towards the end of the rope and the same amount of twine end to melt later.

DSC_7293

It’s a simple tree where the clean up is just rolling up the tree.  When I put up the Christmas lights, I simple wrap them around the edges of the pieces. I usually go in one direction so that the lines are more evenly spaced. Same as my blog post Minimalist Christmas Tree, I hang my ornaments off of the lights. For the more fragile ornaments, I hang them from paperclips and then hang them from the cord.

This was created as an option to not use push pins on the wall, but it was an interesting take on a holiday tree as well. Give it a try if you’re interested, and you can even change out the material I used too.

DSC_7347

DSC_7402DSC_7409DSC_7417

DSC_7488

Minimalist Christmas Tree

11.21.2017

0600

Materials:

  • Christmas lights (Used a 25′-0″ length Christmas Light cord)
  • Ornaments
  • Paper clips (Used 14 for the tree + a few extra)

Tools:

  • Measuring Tape

Christmas is one of those holidays that comes with more decorating than the others. It’s not just the food that’s plentiful, but the decorations as well. Which means of course, that I was determined to minimize my decorations for this holiday.

My family has always used a fake tree so we always knew exactly how much mess to expect when decorating for this holiday. However, I wanted to figure out a way to simplify that. This lead to my Christmas tree design, made up of Christmas lights.

DSC_7454 - Copy

I wanted the base to be 36″ wide, simply because it was the width of a standard door. For a 25′-0″ cord I was using, it seemed like a good base point. I first plugged in my cord and measured out 36″ in the direction I wanted my tree to be located, and then 6″ up. At that point, I placed a pushpin. I then hooked a paperclip to my cord so that it would reach the pushpin. This 36″ length of the cord would create the bottom branch of the tree.

DSC_7783

From there, I measured out 34″ of the next section of the cord and moved in the opposite direction of the bottom branch and measured 6″ up, where I placed the next push pin. I straightened my 34″ section of the cord and placed a paper clip onto it and hooked it onto that pushpin.

I repeated these steps, for each branch of the tree, where each time I subtracted two inches for each branch and measured six inches up to place the next push pin. The height of your tree will really depend on the width of your bottom branch. If you have a longer length of cord and you want the bottom branch to be wider, you can do just that. However, if you have a longer cord and you still start out at a 36″ wide bottom branch, your tree will be taller, which may look just as beautiful.

If you really want to test out how far your can push this design, link up two cords and see how tall you can make it. However, the longer the cord, the wider the base should be. The sequence for each branch will still be the same. The height of this tree ended up at about six feet high from the floor.

DSC_7475
DSC_7463

DSC_7469

I hung my ornaments around each light and distributed them as needed. If you have trouble hanging the ornaments up, hang the lighter ornaments on the lights themselves and hang the heavier ornaments on the pushpins. If you have delicate or fragile ornaments, consider double looping them around a Christmas light or using a paperclip to hang them up by securing it to the branch (the way you secured the previous paper clips to the pushpins).

DSC_7787
DSC_5196

A lot of my ornaments are fairly light and I create ornaments from old keychains I’ve collected over the years. You can click on that blog post, Christmas Ornaments Hack and read about how I made them. It’s interesting when I stand back and look at the tree, because even the keychain pendants have a unique memories tied to them.

You can place a blanket in front of the tree to place presents on and it’ll still look like and regular Christmas Tree. I like to wrap my gifts in reusable fabric and reusable fabric bags and place them under the tree. I wrote about how to create a Zero Waste Christmas or an Eco-Friendly Christmas, in my other blog posts and you can check it out if you’d like any ideas.

Well there you have it, my minimalist Christmas tree. If this works for you that’s great! I hope this blog post inspires you or jogs up some ideas for you.

DSC_7446