Upcycling Milk Crates to a Shoe Rack

02.06.2018

0600

Materials:

  • 2 Milk crates (about 12″ cubes)
  • Twelve 2″ Multi-Purpose Construction Screws
  • (Optional) Three 1″ wood screws – (for creating the holes)
  • 2 Wood boards (12″ x 11-1/4″ x 1/2″)
  • 16 small screws for holding seats in place
  • Pencil

Tools:

  • Power Screwdriver
  • Table saw / Mitre Saw (or saw it by hand with a rip hand saw)

So I needed a small bench shoe rack piece of furniture. All of the designs and products I flipped through on the internet weren’t quite what I had in mind. I needed a fairly short lengthed bench that didn’t need to store a lot of shoes. I also wanted a compact design. I only own six pairs of shoes and I don’t wear them all in the same season so the rest of the room would be for my family.

I knew I had a few milk crates, which I saw the potential use for this project. It was simple idea and I knew what I wanted the final product to look like.

The interior space within each milk crate was 12″ wide, 12″ high and 10-1/4″ deep. The height of the crate was enough room for two levels for shoe storage.

DSC_8825 - Copy

Since I was going to use two milk crates, I went ahead and found two random wood boards about 1/2″ thick. The boards I found were slightly wider than the depth of the crates, but I left the extra inch for larger shoes.

So using a miter saw, I cut each piece of wood board down to 12″ x 11-1/4″.

DSC_8834 - Copy

Next I divided the interior height in half and created a guideline down the middle. Since the crate is plastic, I used an exacto blade to lightly score the midline.

DSC_8837

Using the wood screws and my power screwdriver, I pinpointed the locations of where I wanted my 2″ screws to be located. I like using the wood screws when locating holes in plastic because I can hold the shank of the screw and still guide the power screwdriver to create the straight hole.

wood screw Diagram

DSC_8838

After the holes are created, I took the 2″ Multi-Purpose Construction Screws and screwed them into the premade holes.

DSC_8841DSC_8843

For the four screws that were located further towards the back of the box, I screwed the 2″ Multi-Purpose Construction Screws inwards. And for the two screws located towards the opening of the box, I screwed them outwards.

I wanted the back of the box to be supported more since it was further back. Also, I didn’t want anything sharp located towards the front opening.

DSC_8842 - Copy (2)

I simply install each box with a board, placing the boards on top of the screws. The boards fit well and were snug enough where they didn’t move either.

Most shoes are longer than 10-1/4″, so leaving the extra 1″ helps with different sized shoes. If you need to store boots or shoes that wouldn’t fit the original designed space, you can simply remove one of the boards and the two screws closest to the opening. (I left the two screws here to show the original design)

So there you have it, you can create a simple seat and shoe storage very quickly and with simple materials. You can install a wood board on top to create a bench or stack these crates on top of a 2″ x 4″ frame to have one more level. There’s a variety of designs this can break out into. I might just do that when the spring season rolls around.

Hope this post jogged up ideas!

DSC_8858 - Copy

DSC_8853 - Copy

Update:

I wanted to secure a seat on top of the crates so I took another extra piece of wood board and lined it next to the piece I usually keep on top of the creates.

DSC_9711

I took my pencil and traced the crate pattern on the underside of each board and then used small screws to outline at least two crate holes using the small screws. In order to know where I had to place my screws, I flipped my screws over so that they would be standing on their heads and then gauged where the sharp end of the screw would land. The head of the screws had to hug the insides of the traced corner, so I knew where to place it. Wherever the screw could touch both edges of the location, was where I knew I had to place the screw.

I measured the location for the screws in this manner because I wanted the screw to fit right inside of the hole I traced. The head of the screw as well as the thread of the screws had to fit comfortably into the existing holes, once it was flipped over.

DSC_9708

I didn’t screw the screws in the entire length of the thread, so be very aware of the depth of the wood piece you pick out and the screw length that you choose as well. The idea here was to still have the screws sticking out of the board so it would fit nicely into the holes that were traced.

DSC_9708DSC_9705

Once I placed the boards back onto the crates, the top was created into a quick seat to use while putting on shoes (or taking them off).

 

DSC_9721

So there you have it! I like this much more now with the seat on top, and secured into place.

 

Advertisements

Upcycling Shelves

06.13.2017

0600

Materials:

Tools:

  • Miter saw
  • Electric drill  and drill bits

So my family usually keeps leftover material from previous house projects or from items that were disassembled. A lot of the time wood planks are left over. These vary in sizes so I try to upcycle them around the house. My father had a book shelf a while back and it had two 42″ shelves that were 1″ thick and two 72″ shelves that were one inch thick.

I  knew those shelves could be used elsewhere in the house so I designated the shorter shelves for the upstairs kitchenette and created shelves with the other two longer pieces, in two other separate areas of the house.

I bought four grey Everbilt 10 in. x 8 in. Gray Medium Duty Shelf Bracket for the kitchenette and I bought two white Everbilt 9.75 in. x 7.75 in. White Elegant Shelf Bracket for the shelf in the bedroom. The shelf in the hallway will be mounted up with two wood 2x4s on each side.

For the kitchenette, I located the studs by knocking on the wall (you can also use magnets to locate the nails located in the studs as well) and since I wanted the top shelf to have at least 16″ of space from the shelf to the ceiling, I had to create two marks that marked both the top and bottom of the top shelf. I then measured another 11″ below the bottom line of the top shelf and made two marks for the bottom shelf. I wanted to leave at least 22″ above the countertop so there was enough room for using the countertop surface.

Because the shorter shelves didn’t reach across the wall of the kitchenette, I offset the shelves to make the weight of the items on the wall even. I measured the distance between the studs for each shelf, and transferred that onto each shelf. It’s easier to attach the shelf brackets to the shelves first, and then attach them to the wall. My studs were 30″ (on center) between each, so I knew to leave half an inch from the edge of each shelf edge and then measure inwards 30″ to mark the next center of the next bracket.

Once I attached the brackets to the shelves, I had to pre-drill the holes for the screws in the studs on the wall. If you screw in the top screw on the bracket closest to the wall (where the blue arrow is pointing to), and then place a  small level on top (where the violet arrow is pointing), then you can swing the other bracket up (where the maroon arrow is pointing), until the level shows that the shelf is at an even plane.  This seemed to be the easiest way for me to attach the shelves and also double checking the correct balance of the shelves.

DSC_6193

 

DSC_5564

DSC_5571

For the shelf under the window, I first located where my studs were and made sure I cleared the electrical outlet. Ideally, I would have place a bracket where that electrical outlet is located, but there wasn’t any room. I wanted the height for this shelf to have an 8″ clearance, so I simply measured 8 inches below the existing shelf and marked two lines for the top and bottom of the shelf. For this shelf I trimmed the edges so it would fit the width of this space better. I also drilled a hole above where the outlet was located, so there would be access to the outlet.  I attached the brackets to the shelf based on the width of my studs. For this shelf, I literally held up the shelf with one hand, and traced the inside of the drill hole locations with the other. As long as I continued to press the shelf against the wall, it didn’t move much. I did this because I wanted to mark where the drill holes were and also to pinpoint the center of the holes. There wasn’t room to swing the shelf up to level it out, (such as the kitchenette example), so when I placed the level on the shelf, I only had to adjust the shelf slightly to even it out. Once the first screw was placed, it pretty much held up it’s own weight until I could drill in the last three screws.

DSC_5629

The shelf in the hallway was mounted with a different method. I actually had to cut this original shelf piece in half. It was the other 72″ long shelf piece, and by placing each of the halves next to one another, I created a  18-1/2″ depth shelf. I first located the studs in each wall and measured 11″ height clearance for the space above this shelf.  The width of the space was so small, that putting up brackets would have taken up too much room. I pre drilled the holes in the 2x4s based on the width of my studs I had located. Always remember which 2×4 belongs on which wall, so you’re not accidentally drilling extra holes. After that, I placed each piece on the new mount and held the shelf pieces in place with finishing nails.

DSC_5634

 

This was just one of my upcycling projects using materials I found in the garage. If you can find materials that are still in fairly good shape, I would try to upcycle it for a useful piece of item that you may need. It’s cheaper than going out to buy brand new material- especially since you’ll still have your extra supply of material laying around.  I like to use up what I buy, it’s habit of mine and it’s saved me money over the years. I hope this post helped jog some ideas for you!