How I Keep Long Cords Organized

January 2, 2018August 12, 2018 / Yen-Van Tran / 4 Comments

01.02.2018

0600

Materials:

Velcro straps
Cardboard

Tools:

Cables
Rope
Christmas Lights

Organizing long ropes is always a bit tricky. There are many different methods and techniques that people use in different professions. I discovered a few that help me keep different types of cords organized.

Every cable has a natural coil. When you try to fight that coil, bad things happen. The cable eventually twists on the inside, and when you needed it the most, the cable will fail.

For long extension cords:

For extension cords, I use the “Over-Under Technique” to keep my longer cords in a loop form but also to keep it from twisting was I’m wrapping it up. This method eliminates unnecessary twists in the cord and allows the cord to coil in it’s natural state (like it was wrapped from the factory). You can check out how this technique is used at Digital Photo: “Studio Safety: Coiling Cables”. The technique looks like this:

Basically, you take the cable at one, holding the cable in one hand with your thumb holding that end down. With your other hand, and your thumb facing the same direction as your other hand, bring the cable around to create a loop and let that loop sit in your holding hand.

Then create another loop but face your thumb away from the holding hand’s thumb, bring it around to create another loop, but when it reaches your holding hand, make sure your thumb is facing the opposite direction of the holding hand’s thumb. Repeat these two types of loops until you finish with the entire cable. When you coil your cables in this sequence, the cable does not twist while you coil it up.

If you need to use the cable, you can grab the end of the rope that is on the outside, throwing the coil away from your or just pulling on one end, and the rest of the cable will unravel quickly.

For shorter cables, I wrap the cable around my hand, using the space between my thumb and index finger.

With Christmas lights, I take a piece of cardboard and I cut it into an “I” shape, with small slits cut into the four inside corners of the cardboard piece. These slits are about half an inch and marked where the red lines are located in the picture. If you want to know the measurements for my cardboard holders, I included it in the image below.

Tuck the female end of the christmas lights into one of the slits. Continue wrapping the cord around the middle piece of the cardboard until the entire cord is wrapped. Then take the male end of the cardboard and tuck it into the nearest available slit.

When you need to use the Christmas lights, simply plug in the male end of the cord and unravel while decorating your tree, or just decorating inside as needed.

I also label each cord using masking tape, with that type of light it is (marked with the yellow circle) so it’s easier to identify each year when we set up the Christmas decorations. I also write the length of each cord on both the male end and female end, which is identified with the orange circle.

White Solid = White lights that don’t blink
White Blink = White blinking lights
Color Solid = Color lights that don’t blink
Color Blink = Color lights that blink

So these methods are how I keep my long cords organized and I’m sure there are more techniques as well. Hopefully these ideas will spark some new ways of how you can organize your cords.

How To Daisy Chain Your Long Ropes

December 26, 2017August 12, 2018 / Yen-Van Tran / 2 Comments

12.26.2017

0600

Storing long ropes can be a hassle, but if you know how to organize the ropes, unraveling them each time won’t seem as daunting. I like to wrap my long ropes in a daisy chain so that when I open the rope, it’s a quick process and it doesn’t get tangled.

A daisy chain is a simple method to store long ropes. It’s also known as a chain sinnet. It’s a method of shortening a rope or other cable while in use or for storage. It is formed by making a series of simple crochet-like stitches in the line. It can also reduce tangling while a rope is being washed in a washing machine. Rock climbers, concert stage workers have used this method in their professions. I’ve found that wrapping the ropes up in a daisy chain can be just as quick as unraveling it once you nail the method down.

First find the middle of the rope and tie a knot to mark the middle point. It’s easier to create a loop while making the knot to make it more distinguishable.

At the ends of the rope, tie knots to keep the rope from fraying.

Before starting the chain pattern, it’s easier to step on the two loose ends of the rope so that the chain is taught when you’re creating it. Take the end with the middle knot and loop the other end over it creating a loose loop.

Then bring the rope through the loop you just created.

Pull the new loop through the opening and bring it downwards so that you can see the hanging rope through the new loop.

Grab the rope through the new loop and bring it through, towards yourself.

Once you grab hold of the rope, bring down the chain so that the loop pattern is more taught. Once the pattern is tighter, you can bring the chain back up and repeat the process.

Once you get towards the end of the rope, just grab the leftover rope and pull it through. Make sure the ends of the rope won’t slip through the opening by tightening the last loop.

When you need to use this rope, simply open this end of the daisy chain, give it a little tug and your rope will unfold quickly and easily. I’m sure there are other methods of storing long rope, but this is my favorite way of storing my own. I usually use these ropes in my Sport Emergency Kit, so it comes in handy when I’m in the snow. This method also allows for a quick unravel for my gloved hands.

I hope this blog post helps you store your long ropes if you choose the Daisy Chain Method.

Creating A Locking Mechanism For My Carabiners

May 16, 2017August 12, 2018 / Yen-Van Tran / 1 Comment

05.16.2017

0700

I’m a big fan of carabiners. I have all different types and designs, however, I tend to favor the Asymmetrical D-Shape. On a whim a few years back, I bought two S-Binder carabiners. I really liked this design because the items I would place on the bottom half of the carabiner were separated from the top half. The top lever was the lever that I would use to hook and unhook the carabiner to other objects.

This also lead to an issue with the way in which I used it. Each time I would wrap my hands around the carabiner to press open the top lever, I would inadvertently press my palm against the bottom lever and the objects had a very good chance to slide out. This involuntary action happened a few times and I had to come up with a quick solution.

First, I wrapped a small piece of Velcro around the bottom lever, but over time, the Velcro started to become weaker and would become unattached, which left the end flap of the Velcro unattached. I knew I had to come up with a more permanent solution. I knew other carabiner brands sold their Asymmetrical D-Shape carabiners with locking mechanisms or had an external accessory that helped lock their levers in place. I had to make my own locking mechanism in order for me to not drop my keys all over the place.

I took a old piece of an iron on elbow patch (I had bought a set years ago and never used them all up), and I cut the length to the distance that it would take to cover the lever and half of the basket of the carabiner. (If you don’t know where the ‘basket’ is, I labeled all of the parts of a carabiner in the first image).

With a few sewing needles, I marked the locations of the fabric of which I would have to sew the fabric together. I removed the fabric from the carabiner and sewed it up. I needed to create a snug fit for the locking mechanism so that the fabric didn’t move easily when in use. When I sewed my second locking mechanism, I sewed it a little too snug, but with fabric, you have a slight chance to stretch the length and width of any product due to the material. This was material for iron-on elbow patches, so it was a very, very slight stretch .

Once I was finished sewing both the locking mechanisms, I slid the pieces on, moved my key rings over them and then slid it back over the levers. It’s a simple solution to a very basic tool I use everyday.

If you use any other kind of fabric, perhaps 100% cotton, you may have to sew it a little tighter because cotton tends to stretch more. And, you may want to extend the length of the locking mechanism so that it can’t slide back and forth on the basket as easily. The idea is to make the fabric slight “stuck” on the spine of your carabiner. If it has a hard time sliding around the basket, then it most likely won’t slide around when in use.

I hope this might give any of you some ideas as to how to approach design problems such as this one. Happy sewing and don’t loose those keys!