design life hacks

12.23.19

0600

Materials:

Fabric piece – 28″ x 17″
Ribbon – 38″ long

Tools:

Sewing Kit
Sewing Machine
Ruler
Blue Ink pen (if using a dark fabric) OR Washable crayon

So I wanted some type of organizer for my makeup and my makeup brushes. A lot of the organizers that I found in stores, only organize make up brushes, but I wanted an organizer that I could also organize my makeup pallets as well. I just wanted some type of organizer that could organize multiple beauty products. Since I couldn’t find one, I decided to make it.

I found two pieces of black fabric that’s were 17″X28″. Both pieces of fabric are a cotton blend and are usually used to make dress pants. I knew the fabric would be durable for this project.

First, I hemmed all the edges. Since I hemmed all the edges at 1/2″ in width, and I folded each edge over twice, the final size of the fabric piece was 15″x26″. Essentially, I had used up an inch of fabric on each side.

My makeup brushes averaged a height of 7.5″, so I knew that my makeup wrap would ideally be 8″ high.

I decided that I wanted 4.5″ base, to hold all of the items in place. I folded the bottom of the wrap, up 4.5″ and pinned the fabric together using sewing pins. I then folded my wrap in half, to find the center line. I wanted the right side of the wrap to hold my brushes and the left side of my wrap to hold my makeup palettes, combs, mascara, eyeliner, etc. I wanted my wrap to be able to hold more than just make up brushes.

Using a washable white crayon, I marked off 1″ sections, for my brushes and then divided the other half into two 3″ sections and two 3.5″ sections. Three inches seemed like a good width for makeup palettes, but check the width of your palettes to see if you need a wider section. I wanted the last two sections on the left side to be 3.5″, because I have a feeling that I’ll need slightly larger slots in the future.

In addition to the washable crayon, I also used a blue ink pen to draw guide lines for the slots, so I could sew the lines straight, when using my sewing machine. The blue ink blends in with the black fabric, so it was only visible under the sewing machine light bulb. I also could have used the washable crayon to mark off the guide lines as well.

Usually, when I create any sewing project, I try to end the sewing line, close to the edge of the fabric. It’s easier to create the back stitch when it’s close to the edge of the fabric.

In this case, I started my sewing line near the top of the folded flap, used the back stitch lever to create a back stitch, continued to sew down the guild line, and then ended the line at the bottom edge, with another back stitch as well.

Since the wrap was long, I folded the right side of the wrap inward, so I could still keep the shape of the wrap neat and clean as I fed the fabric through the presser foot and needle of the machine.

I wanted all of the sewing lines to start at the hem line, because I thought it would create a cleaner look for the wrap.

After I finished sewing all of the slot lines, I wanted to create a top flap, that would cover the makeup bristles and ferrules. I simply folded the top edge of my wrap down 3″, and ironed that edge.

I took my ribbon, and I folded it in half. I needed to find the center line of the ribbon, so I can line up with the center line of the last slot on the left side. I wanted my makeup brush wrap to unroll to the right, so I had to attach the ribbon on the left back side. The wide slots on the left also provide a good section to attach the ribbon to.

The location of where I sewed the ribbon was based on the location of the heels of my brushes. The heels of my brushes were close to the middle of the wrap. It was also the location where my ribbon had to wrap around in order to contain the entire wrap securely.

Using a sewing pin, I pinned the ribbon to the wrap, and sewed the ribbon to the back of the last left slot. I wanted a really long ribbon for this makeup brush wrap, because I wanted to be able to wrap the ribbon twice around the entire wrap, if needed.

So this is what the finished product ended up looking like. The bottom picture is what the wrap looks like when it is wrapped up.

11.18.2019

0600

So this blog post is a personal life hack of mine. When I work out, I like to wear sweaters. Now, these sweaters are not always athletic sweaters, but simple sweaters that I buy just to wear on a day-to-day basis. I like to go running in these sweaters because they’re comfortable and warm. However, when I go running with these sweaters, the sleeves tend to run up my arm. I prefer the sweaters to cover my wrist and not bunch up when I’m running. I like the running sweaters that are designed with thumb loops, but they tend to be more expensive as well. Since I love my sweaters that I wear day to day, I decided to create my own thumb loops for my sweaters.

It’s a very simple process to create these thumb loops. First, I laid down my sweater where the sleeve lay flat on the table. I located the center line of the sleeve, and then chose to locate my thumb loop on the bottom half of the sleeve, but on the cuff of the sleeve. I found the center line of the bottom half of the sleeve, and I decided to locate my new thumb loop there.

When I wear my sweaters, my hand falls naturally to my side, in which my thumb faces towards the front of my body. This is why I located the thumb loop on the bottom half of the sleeve.

I wanted my thumb loop to be 1 inch in length and about half an inch from the bottom of the sleeve cuff. Using scissors, I cut a small slit that was 1 inch in length.

For my right sleeve, I used the same process as I did with the left sleeve. I located the center line of the right sleeve, and then located the center of the bottom half of the sleeve. I cut a one inch slit that was half an inch away from the bottom of the sleeve cuff.

I removed my extension table in order for the sleeve to fit underneath the presser foot of the machine. I slid the left cuff over the needle plate and started to sew the edge of the thumb loop. I used a tight zigzag stitch, so the fabric would hold up during washes and use. Since I knew that these thumb loops would go through a bit of wear and tear, I used the back stitch lever to create a strong and permanent attachment at the ends of the thumb loops.

The back stitch lever created the heavy and thicker starting points and end points of the outline of the thumb loops.

I flipped my left sleeve inside out, and continued to outline the other side of this thumb loop. I used the zigzag stitch again and used the back stitch lever so both ends of the opening would have an even reinforcement, of the thumb loop.

When I turned my sweater inside out, the thumb loops were finally finished being created. I use this hack on both of my sweaters, so now the sleeves won’t run up my arms when I workout.

This is a really simple hack for an issue that I dealt with on a daily basis. Although I know my thumbs will stick outside of my sleeves, when I run,they don’t get too cold. Sometimes I will run with my running gloves when the weather drops too low, so technically, my hands are still warm. Some people prefer to not have the thumb loops, but I like to keep my wrists covered when I run. This hack took less than 30 minutes to create and finish, so it didn’t take much time out of my day at all. I hope this hack will inspire other hacks that you might be needing in your life.