DIY Makeup Wrap

December 23, 2019December 22, 2019 / Yen-Van Tran / Leave a comment

12.23.19

0600

Materials:

Fabric piece – 28″ x 17″
Ribbon – 38″ long

Tools:

Sewing Kit
Sewing Machine
Ruler
Blue Ink pen (if using a dark fabric) OR Washable crayon

So I wanted some type of organizer for my makeup and my makeup brushes. A lot of the organizers that I found in stores, only organize make up brushes, but I wanted an organizer that I could also organize my makeup pallets as well. I just wanted some type of organizer that could organize multiple beauty products. Since I couldn’t find one, I decided to make it.

I found two pieces of black fabric that’s were 17″X28″. Both pieces of fabric are a cotton blend and are usually used to make dress pants. I knew the fabric would be durable for this project.

First, I hemmed all the edges. Since I hemmed all the edges at 1/2″ in width, and I folded each edge over twice, the final size of the fabric piece was 15″x26″. Essentially, I had used up an inch of fabric on each side.

My makeup brushes averaged a height of 7.5″, so I knew that my makeup wrap would ideally be 8″ high.

I decided that I wanted 4.5″ base, to hold all of the items in place. I folded the bottom of the wrap, up 4.5″ and pinned the fabric together using sewing pins. I then folded my wrap in half, to find the center line. I wanted the right side of the wrap to hold my brushes and the left side of my wrap to hold my makeup palettes, combs, mascara, eyeliner, etc. I wanted my wrap to be able to hold more than just make up brushes.

Using a washable white crayon, I marked off 1″ sections, for my brushes and then divided the other half into two 3″ sections and two 3.5″ sections. Three inches seemed like a good width for makeup palettes, but check the width of your palettes to see if you need a wider section. I wanted the last two sections on the left side to be 3.5″, because I have a feeling that I’ll need slightly larger slots in the future.

In addition to the washable crayon, I also used a blue ink pen to draw guide lines for the slots, so I could sew the lines straight, when using my sewing machine. The blue ink blends in with the black fabric, so it was only visible under the sewing machine light bulb. I also could have used the washable crayon to mark off the guide lines as well.

Usually, when I create any sewing project, I try to end the sewing line, close to the edge of the fabric. It’s easier to create the back stitch when it’s close to the edge of the fabric.

In this case, I started my sewing line near the top of the folded flap, used the back stitch lever to create a back stitch, continued to sew down the guild line, and then ended the line at the bottom edge, with another back stitch as well.

Since the wrap was long, I folded the right side of the wrap inward, so I could still keep the shape of the wrap neat and clean as I fed the fabric through the presser foot and needle of the machine.

I wanted all of the sewing lines to start at the hem line, because I thought it would create a cleaner look for the wrap.

After I finished sewing all of the slot lines, I wanted to create a top flap, that would cover the makeup bristles and ferrules. I simply folded the top edge of my wrap down 3″, and ironed that edge.

I took my ribbon, and I folded it in half. I needed to find the center line of the ribbon, so I can line up with the center line of the last slot on the left side. I wanted my makeup brush wrap to unroll to the right, so I had to attach the ribbon on the left back side. The wide slots on the left also provide a good section to attach the ribbon to.

The location of where I sewed the ribbon was based on the location of the heels of my brushes. The heels of my brushes were close to the middle of the wrap. It was also the location where my ribbon had to wrap around in order to contain the entire wrap securely.

Using a sewing pin, I pinned the ribbon to the wrap, and sewed the ribbon to the back of the last left slot. I wanted a really long ribbon for this makeup brush wrap, because I wanted to be able to wrap the ribbon twice around the entire wrap, if needed.

So this is what the finished product ended up looking like. The bottom picture is what the wrap looks like when it is wrapped up.

DIY Thumb Loops In Sweater Sleeves

November 18, 2019November 25, 2019 / Yen-Van Tran / Leave a comment

11.18.2019

0600

So this blog post is a personal life hack of mine. When I work out, I like to wear sweaters. Now, these sweaters are not always athletic sweaters, but simple sweaters that I buy just to wear on a day-to-day basis. I like to go running in these sweaters because they’re comfortable and warm. However, when I go running with these sweaters, the sleeves tend to run up my arm. I prefer the sweaters to cover my wrist and not bunch up when I’m running. I like the running sweaters that are designed with thumb loops, but they tend to be more expensive as well. Since I love my sweaters that I wear day to day, I decided to create my own thumb loops for my sweaters.

It’s a very simple process to create these thumb loops. First, I laid down my sweater where the sleeve lay flat on the table. I located the center line of the sleeve, and then chose to locate my thumb loop on the bottom half of the sleeve, but on the cuff of the sleeve. I found the center line of the bottom half of the sleeve, and I decided to locate my new thumb loop there.

When I wear my sweaters, my hand falls naturally to my side, in which my thumb faces towards the front of my body. This is why I located the thumb loop on the bottom half of the sleeve.

I wanted my thumb loop to be 1 inch in length and about half an inch from the bottom of the sleeve cuff. Using scissors, I cut a small slit that was 1 inch in length.

For my right sleeve, I used the same process as I did with the left sleeve. I located the center line of the right sleeve, and then located the center of the bottom half of the sleeve. I cut a one inch slit that was half an inch away from the bottom of the sleeve cuff.

I removed my extension table in order for the sleeve to fit underneath the presser foot of the machine. I slid the left cuff over the needle plate and started to sew the edge of the thumb loop. I used a tight zigzag stitch, so the fabric would hold up during washes and use. Since I knew that these thumb loops would go through a bit of wear and tear, I used the back stitch lever to create a strong and permanent attachment at the ends of the thumb loops.

The back stitch lever created the heavy and thicker starting points and end points of the outline of the thumb loops.

I flipped my left sleeve inside out, and continued to outline the other side of this thumb loop. I used the zigzag stitch again and used the back stitch lever so both ends of the opening would have an even reinforcement, of the thumb loop.

When I turned my sweater inside out, the thumb loops were finally finished being created. I use this hack on both of my sweaters, so now the sleeves won’t run up my arms when I workout.

This is a really simple hack for an issue that I dealt with on a daily basis. Although I know my thumbs will stick outside of my sleeves, when I run,they don’t get too cold. Sometimes I will run with my running gloves when the weather drops too low, so technically, my hands are still warm. Some people prefer to not have the thumb loops, but I like to keep my wrists covered when I run. This hack took less than 30 minutes to create and finish, so it didn’t take much time out of my day at all. I hope this hack will inspire other hacks that you might be needing in your life.

Sofa Armrest Organizer

October 14, 2019October 14, 2019 / Yen-Van Tran / Leave a comment

10.14.19

0600

Materials:

Two Curtains at 5′-10″ in length

Tools:

Sewing Machine
Sewing Kit

I have an extra set of curtains, which I didn’t want to use anymore. I decided to create a sofa armrest organizer with both curtain pieces. Both curtain pieces were 5 foot 10 in length, and 27 inches wide.

I wanted my sofa armrest organizer to sit at a certain height off the ground, but I also wanted the top half to also tuck underneath the couch cushion. I first measured how high off the ground I wanted my couch armrest organizer. Since I needed to hang it over the sofa armrest and then wrap back over the arm to tuck underneath the cushion, that left about 47 inches to tuck underneath the cushion.

I wanted to store books in the first organizer, which would be fairly heavy, so I needed a lot of the material to tuck under the seat cushion to hold it in place. I actually wanted the top part of the organizer to tuck underneath an entire sofa cushion width, due to the weight that would be applied.

FIRST SOFA ARMREST ORGANIZER:

When I measured out my first design, I wanted the pockets for my books to be 14 inches in height. I first hemmed all of the edges and then I folded one edge to create the 14″ tall pockets. I sewed around the edge of the folded piece (yellow arrows) and then divided the pocket in half, and sewed a dividing line down the center to create two tall pockets (red arrow). These pockets will be able to hold my books and paperwork that I’m currently working on. I wanted my pockets to be a bit taller than the standard paper size (8.5″ x 11″), due to the fact that I knew the width of the pocket might eat up some of the height. I also wanted to be able to hide my books and paperwork, so my pockets wouldn’t look like they were overflowing with paper.

To attach the sofa armrest organizer, I removed the couch cushion on the side of the couch, located how high I wanted to hang the organizer, and then replaced the couch cushion. Since the top half of the fabric organizer is tucked under the couch cushion, it stayed in place.

SECOND SOFA ARMREST ORGANIZER:

I also wanted to create a second design, which would have smaller pockets for smaller items. My second design would have 10 inches in height for the books, and 6 inches for smaller objects.

Using the same sewing method as the first design, I hemmed all of the edges of the fabric material, and then measured 16″ of material at one end. I folded up the 16″ material, sewed along the outside edges of the tall pocket (yellow arrows), which created a giant 16″ tall pocket.

I then took the bottom 6″ of the pocket and folded it up, to create a shorter 6″ pocket at the bottom. This 6″ tall pocket also helped create the 10″ pocket behind the smaller pockets. I then sewed on both of the side edges of the fabric piece (red arrows) and then sewed a dividing line (blue arrow) to create a total of four pockets for this design. I sewed the edges of this design, all the way to the top of the pocket to reinforce the side edges.

Using the same method as the first sofa armrest organizer, I located where I wanted the organizer to hang on my armrest and I tucked the top half of it under the couch cushion on the end.

Since these sofa armchair organizers are made of fabric material, I can toss them into the washing machine and wash them easily. I can also fold them up and put them away if I don’t need to use them. Fabric is my favorite material to work with since it can be taken apart and reused multiple times. I love that it is a very flexible medium and I was able to put my old curtains to good use.

How I Organize My Jewelry

September 9, 2019September 27, 2019 / Yen-Van Tran / Leave a comment

09.09.2019

0600

So I’m a simple girl which means I have simple ways of organizing my life as well. Since I am a minimalist, I actually don’t own a lot of jewelry. So, I thought I would show you how I organize my jewelry.

When I was a kid, my necklace always became tangled, no matter how I seemed to store it. I didn’t really figure out how I wanted to organize my jewelry until later on. Parts of my jewelry organization was due to the fact that I didn’t have that much jewelry to organize when I get older. It actually really helps my life to organize less stuff than more stuff.

I thought I would show you how I organize my necklaces, bracelets, and earrings

For my necklaces I like to use a Velcro strap, in which all I have to do is grab the Velcro loop and my necklaces fall naturally in an organized fashion, due to gravity. I also use a Velcro strap to organize my bracelets. For some of my necklaces I like to use a binder ring, because the design gets caught on the Velcro, when I lift it up. But for the most part, I’ll use Velcro straps. I also like using the Velcro straps due to the flexibility that it allows. If I need more space, to organize my jewelry, it allows that need.

I use a Velcro strap to organize my bracelets. One of my bracelets is fairly wide in shape so I needed something that was flexible to it.

My earrings are organized a fairly special way. I never really had a clear way of organizing my earrings up until I just thought, “Why not just attach them to a piece of fabric?”. So that’s exactly what I did. I sewed a piece of extra fabric to the inside of my jewelry pouch, and I just attach my earrings to the fabric. I actually pre-punch holes using a pushpin something generic and I just attach my earrings to those pre-made holes. I like this design because of the fact that the earrings don’t get lost and the backing of the earrings are still protected by the extra piece of fabric.

The fabric piece flips out, to access the earrings easier. I also keep my extra earring backings on a small safety pin that’s attached to a ring. I have quite a few extra earring backings, so, I have quite a few safety pins on the ring.

I created an extra detachable fabric earring piece for traveling as well. This travel earring organizer is used when I need to use different backpacks or bags while traveling. It’s used for trips when I don’t want to bring my entire jewelry pouch.

I organize my rings in a similar manner, where I keep them organized on a small necklace chain. The necklace chain for my rings is kept with my other necklaces. It’s easy to lift up the necklace chain and have the rings fall naturally. When I travel, I will keep my rings organized on a carbiner, but most of the time, they stay on a necklace chain. They don’t get tangled, and they stay organized, due to the sequence I arranged them in.

So, that’s how I organize my jewelry. If I ever acquire more jewelry, or a bigger bag, I’ll likely use the same techniques and system that I have for this bag. Hopefully, some of the methods I’ve shown you here, might spark and idea for your organization system.

Upcycling A Shoe Organizer

October 2, 2018October 2, 2018 / Yen-Van Tran / Leave a comment

10.02.2018

0600

Materials:

One over the door shoe organizer
X-acto blade
Cutting mat (or cardboard, plywood, some type of surface you’re willing to cut into and can damage just a little bit)
4 Safety Pins

Tools:

Sewing machine
Sewing Kit

So I’ve owned an over the door shoe organizer for awhile. I didn’t use it a lot because I didn’t have many pairs of shoes. When I started to declutter my life and minimize my possessions, I kept it because I still liked the design and I knew I could use the material to create something else.

Because I’m not a fan of keeping items out in the open, much less hanging them out in the open, I knew I wanted to upcycle this shoe organizer into smaller organizers. I personally like things to be put away. My minimalist, zero waste lifestyle lends my living space towards clean surfaces and minimal decor. So I wanted to create two smaller organizers which could be hung up in the closets.

The goal was to create two separate organizers that were each 2 pockets across by 3 pockets vertically on each side of the smaller organizer. So each side of the hanger would hold a grid of pockets that was 2 pockets across by 3 pockets vertical.

First I cut the shoe organizer in half.

I then folded each organizer in half (vertically) to find out where I wanted to locate the hangers.

I then placed each hanger on each organizer, as I wanted them to sit. I wanted to place each hanger so that the top bars of the hangers would still be protected by the fabric. I only wanted the neck of the hanger to stick up and out of the fabric so the fabric organizer would sit higher on the hanger. The hanger would have more control of the overall weight of the items inside each pocket when it was hung up.

I placed the hangers where I wanted each hanger to be located on each organizer and then marked the location of the bottom bar. I needed to make a mark at those locations, because that’s where the bottom of the openings for the hangers would pass through.

Using the X-acto blade, on the folded edge, I carefully cut a straight line of where the hanger would stick out. I cut along the mid line of the fabric grid pattern and only cut enough for the hanger to fit. You can sew the edges of these openings if you want a clean and sturdy structure around the edge of the opening. I suggest using a running stitch to do that, if you choose to.

Using the bottom of opening as a location marker, I sewed both sides of each organizer together. I wanted the backs folded and sewed to one another to create a more sturdy central structure. I sewed from the bottom of each opening, around and up to the other side, making sure I stopped at the other marker.

The idea was that I wanted to seal the two flaps of pockets to each other, but leave enough room for the hanger to slide in and out of the design.

Once the hanger is slid into place, the flap should allow the user to remove the hanger if necessary. I used a hem stitch to secure the top of the opening on the folded edge (see below). I did this because I know that the weight of the the organizer will tear the opening over time. I wanted to secure the top of the opening and reinforce the structure.

I stitched an extra line above the hanger (towards the folded side of each hanger), but underneath the pocket flaps, to reinforce extra support for the organizer.

Using a safety pin, I pinned the opened edge approximately where the top of the hanger was located on the opposite side. This way, the hanger can be removed easily when it comes time to wash it or put it away. The safety pin will act as a closing mechanism to hold the hanger in place.

So there you have it, this is how I upcycled my over the door shoe organizer. Although, I technically only created smaller shoe organizers, I had the idea that I could use these smaller organizer to store smaller items such as jewelry, scarfs, socks, etc., that can get lost in a closet. Basically, anything you might store in the top drawer of your dresser, you might use this for. I don’t use a dresser, so this product can be useful for me. Right now I actually use a few of the pockets to keep some running and workout items organized. I like this design for the fact that it’s double sided and it can be folded up and put away if it’s not being used. Hopefully this post might spark some organizational ideas for your life.

Until next time!

Quick T-Shirt Pocket

September 11, 2018September 26, 2018 / Yen-Van Tran / Leave a comment

09.07.2018

0600

Materials:

One T-shirt (or two, but definitely at least one)

Tools:

Sewing machine
Sewing Kit

Living a Zero Waste life means that I create simple solutions for simple problems since I don’t want to go buy anything new or seek out another possession to take care of.

So I usually carry my phone around with me when I’m doing certain types of household tasks. These tasks don’t require a lot of vigorous movement, but I’m definitely moving around. A lot of the time it’s annoying to remember to carry the phone from one place to another when I’m running around the house and if my hands are dirty, I really don’t want to touch my phone. I needed a quick solution where I could carry the phone along with my keys without much hassle. I didn’t want to go out and buy a separate cell phone holder strap that would wrap around my arm. I have one for workouts, and that strap holds down my cell phone securely since I’m running. But I just needed a quick solution where I could carry around my phone and my keys easily for a few hours.

My quick solution was to see my t-shirt sleeve in half and create a pocket. my t-shirt sleeves are usually longer than I need them to be. This gave me the extra material to work with. I simply folded my sleeve in half and pinned the sleeve all the way around.

Depending on the width of your cell phone, measure that distance out on the top of the sleeve. Just make sure you divide the width of your phone in half and center the opening on the top of the sleeve.

For the other sleeve, I made the opening just about the same size since I knew I was going to use the other pocket for keys or my credit card.

Then just sew the sleeve from the front to the back or back to the front, making sure you still leave enough room for your cell phone. Then tie off the open thread ends.

If you put smaller items in the short pockets, they tend to fall towards the bottom of the sleeve. This can be annoying for some but for me it gives me a sense of security knowing my items won’t fall out. I just need to go fishing for my keys at the end of the day.

So there you have it. My quick and dirty solution to built in t-shirt pockets. I like to move the pockets towards the front of my body for easier access to my cell phone, but that’s simply more comfortable for me. I also will sometimes secure the t-shirt using a binder clip, that I’ll use to clip my t-shirt to my bra.

Upcycling Denim Jeans

January 30, 2018August 13, 2018 / Yen-Van Tran / 5 Comments

01.30.2018

0600

Materials:

One pair of denim jeans

Tools:

Sewing machine
Sewing Kit

So recently I started going auditing my traveling items such as my bath bag, travel accessories as well as my sport bags. I wanted to find 3 pieces of clothing to donate, but I also noticed that my bath bag wasn’t containing my bath items comfortably.

So I had the choice to go buy/find a new bath bag or find another solution. Out of the items I decided to donate, I found a tank top, sweater and a pair of jeans. Denim is one of my favorite materials to work with. I love upcycling denim into new items. The idea of donating the pair of jeans wasn’t exactly what I thought I would do, so I decided to make a stand up bath bag for myself, or at least a few stand up bags.

I’ve owned bath bags before, but the material was with a polyester or nylon blend. Over time, my bath bags would have soap or toothpaste residue stains. I figured that with a denim bath bag, I could simply throw it into the washing machine and it would clean easily.

I divided each leg in half by folding it in half. I then cut the legs off from the pair of jeans and then divided each piece in half.

I turned each of them inside out and designated the wider end of the pieces as the bottom of the bag and the smaller ends as the top of the bag. I folded the top of the bags down to create the drawstring tube. This is where I wanted to install the drawstring later.

DSC_8697 - Copy

I hemmed the bottoms of the bags by simply sewing a sew line across the bottom. I then sewed the drawstring tube. I measured 2″x2″ squares on the corners on bottom.

I marked these white dots on BOTH SIDES OF THE BAG, near the bottom section of the bag. These white dots will be used as guides of where you will sew in the next step.

DSC_8699 - Copy

I then flipped the bag upside down, and so that the right side seam was facing up. I then folded the bottom of the bag to create a diamond shape. You should be able to locate all four dots that were created in the last step, when molding the diamond shape.

DSC_8704 - Copy

The dots are guides to sew where you will sew horizontally across the diamond. After sewing the two lines, the diamond should look like this.

Since I was initially thinking of making a new bath bag, I wanted to sew a small pocket inside of that bag. I had this extra pocket left over from my Handmade Handkerchiefs project, so I added it on the inside. To find the opposing edges of the box, you can locate it by finding the perpendicular lines of the top and bottom hemmed lines.

DSC_8715 - Copy

If you want to make a small pocket inside, you can sew a piece of material to the inside of the bag, as long as you leave to top of the material open.

In this case, because the pocket was more than half of the height of the bag, I placed the pocket towards the bottom of the bag. I also knew that I would be folding the bag down when in use, so placing it towards the bottom gave me room for the top to be folded down.

Once I pulled the drawstrings through the bags, this is what they looked like. They stand up pretty well, and I can fold them down to create a top frame for the boxes.

This is what my bath bag looks like now.

I like the fact that I can simply fold my bag down and be able to access everything I need inside. I also have the habit of attaching a ring to the interior of any bag. So I attached a metal ring to the inside seam of the bag, because I wanted to hang small bath items for easy access.

So there you have it. This was my solution to my travel bath bag issue. I genuinely love denim and to make these stand up drawstring bags with this material is one of my favorite kinds of sewing projects that I like to get involved in.

I used my other bags for some camera gear and for another bag I use for traveling. The denim creates a nice thickness for the bottom of these bags, which is why I like to use them for electronics.

As a bonus…

I made a bag out of the top part of my denim jeans. I simply flipped the top inside out and hemmed the pant leg openings. Due to the nature of how the jeans were cut and sewed, I folded the outer edges of the jeans inward when I hemmed them.

I then sewed a zipper to the top opening of the jeans using sewing pins to hold the zipper in place and then sewing it to my pants. I used the same sewing steps to attach the zipper as to when I Created Slim Hanging Organizers.

Since my zipper wasn’t quite long enough for the length of the jeans, I closed off the jeans by sewing the top together.

I used an extra tie to create the handles of this bag. This was a simple choice but some people may prefer to use a belt or something more to their taste. I chose the tie because I wanted to be able to throw everything into the washing machine.

And as always, I attached a metal ring to my zipper for a slightly easier access.

I use this bag to hold some smaller items that need a bit of cushion like camera gear or smaller electronics.

Handmade Handkerchiefs

October 3, 2017August 12, 2018 / Yen-Van Tran / 2 Comments

10.03.2017

0600

Materials:

A few shirts (I used collar shirts for the fact that I like this material and these were extra shirts I found)

Tools:

Sewing machine
Sewing Kit

So there was a recent heat wave that spread through California, and it was HOT. I only had two handkerchiefs and those were being used up fast. I knew I needed more. Although I could have bought a set of twelve for about $5.00. I thought making my own would be more fun.

I found some old collar shirts, that had never been worn (and would never be worn) to make into handkerchiefs. Since these shirts were dress shirts with a tight thread weave, I knew these would be durable over time and the material was still 100% cotton.

I had no idea how many handkerchiefs I would produce from these three shirts so I was curious about the end product. Most handkerchiefs are square shaped and I knew these would vary in size, so I kept that in mind. My current handkerchiefs were 10″ x 10″.

First I took apart each shirt. this meant I had to tediously unravel each thread that made up these shirts. This took awhile to do since certain parts of the shirts had double layers. I also needed to be able to look at each piece of each fabric that made up these shirts. I needed to be able to size up my handkerchief template accordingly.

Once I took apart all of the fabric pieces that made up my shirts, I started to map out 10″x10″ sections on the fabric. There were pieces that I knew I could not use, such as the cuffs and collar of the shirts. For these pieces, I put them aside for future projects. Parts of the shirts such as the Yoke, would have to be sewn together to create enough surface area for a handkerchief.

Due to the shape of each piece of fabric, I wasn’t able to make perfect 10″x10″ squares. Instead, the shape of the fabric pieces gave me some very unique shapes to use for handkerchiefs. Who said a handkerchief had to be a perfect square anyway?

For each piece of handkerchief, I hemmed the edges by first folding in the edges in to create a margin of 1/4″ and pinning them down with sewing pins. From there, I simply sewed the edges down and tied off the leftover thread.

From the three collar shirts, I originally started out with, I was able to make a total of 47 handkerchiefs. The breakdown is:

six – 9″x10″
six – 11″x11″
twelve – 10″x12″
six – 9″x12″
twelve – 10″x18″ (used for cloth napkins)
five – 8″x10″

Because the result of the shirts varied in size and shape, I decided to use the twelve 10″x12″ for napkins instead of handkerchiefs (Luckily I ended up with twelve in this size).

This was a fun upcycling project that took me longer than expected. Taking apart the shirts was the most time consuming, but it was well worth it in the end. Handkerchiefs don’t need to be perfect squares, but preferably 100% cotton. I hope this post inspires you to give it a try to making your own handkerchiefs as well. I’ve learned that although carrying around a handkerchief is an old tradition and I personally don’t see it practiced too often where I live, having one handy can be a lifesaver. Sometimes I’ll use it as a napkin when I don’t have my reusable cloth napkin available. And sometimes, when a stranger needs a kleenex, I’ll give my handkerchief for them to use. I have so many that I can give it away as well. It’s a gesture out of love and caring for humanity.

Creating A Locking Mechanism For My Carabiners

May 16, 2017August 12, 2018 / Yen-Van Tran / 1 Comment

05.16.2017

0700

I’m a big fan of carabiners. I have all different types and designs, however, I tend to favor the Asymmetrical D-Shape. On a whim a few years back, I bought two S-Binder carabiners. I really liked this design because the items I would place on the bottom half of the carabiner were separated from the top half. The top lever was the lever that I would use to hook and unhook the carabiner to other objects.

This also lead to an issue with the way in which I used it. Each time I would wrap my hands around the carabiner to press open the top lever, I would inadvertently press my palm against the bottom lever and the objects had a very good chance to slide out. This involuntary action happened a few times and I had to come up with a quick solution.

First, I wrapped a small piece of Velcro around the bottom lever, but over time, the Velcro started to become weaker and would become unattached, which left the end flap of the Velcro unattached. I knew I had to come up with a more permanent solution. I knew other carabiner brands sold their Asymmetrical D-Shape carabiners with locking mechanisms or had an external accessory that helped lock their levers in place. I had to make my own locking mechanism in order for me to not drop my keys all over the place.

I took a old piece of an iron on elbow patch (I had bought a set years ago and never used them all up), and I cut the length to the distance that it would take to cover the lever and half of the basket of the carabiner. (If you don’t know where the ‘basket’ is, I labeled all of the parts of a carabiner in the first image).

With a few sewing needles, I marked the locations of the fabric of which I would have to sew the fabric together. I removed the fabric from the carabiner and sewed it up. I needed to create a snug fit for the locking mechanism so that the fabric didn’t move easily when in use. When I sewed my second locking mechanism, I sewed it a little too snug, but with fabric, you have a slight chance to stretch the length and width of any product due to the material. This was material for iron-on elbow patches, so it was a very, very slight stretch .

Once I was finished sewing both the locking mechanisms, I slid the pieces on, moved my key rings over them and then slid it back over the levers. It’s a simple solution to a very basic tool I use everyday.

If you use any other kind of fabric, perhaps 100% cotton, you may have to sew it a little tighter because cotton tends to stretch more. And, you may want to extend the length of the locking mechanism so that it can’t slide back and forth on the basket as easily. The idea is to make the fabric slight “stuck” on the spine of your carabiner. If it has a hard time sliding around the basket, then it most likely won’t slide around when in use.

I hope this might give any of you some ideas as to how to approach design problems such as this one. Happy sewing and don’t loose those keys!

A Climber’s Guide To Carabiners

Alternative Dish Scrub

November 15, 2016August 12, 2018 / Yen-Van Tran / 1 Comment

11.15.2016

0800

Materials:

Two Laundry Mesh Bags
Sewing Kit

There are a few things that I struggled with replacing in the zero waste lifestyle realm. The dreaded dish scrub was always one that I consistently tried to tackle with different alternative solutions. So breaking away from the traditional dish sponge was an issue I constantly had to re-visit.

At first, I tried to use cotton dishrags, but I wasn’t a fan of the oil and stains that would show up, even after throwing it into the washing machine. I then moved to the stainless steel sponge, but at times, this material was unnecessary and a little harsh on my dishes. I needed something that fell between these two materials. I needed a zero waste solution that was durable, breathable, washable and readily accessible.

So I finally decided to tackle this issue once and for all, and I came up with a solution. I made my own dish washing srubs from laundry mesh bags. So this is what I did…

I took a delicates, laundry mesh bag with small holes and one with large holes, and took them apart. I separated all the pieces that assembled it. I choose the two different sized holes so there would be more grit during scrubbing and more variety in the uses.
I unstitched the bags to remove zippers and separate the individual pieces.
I then folded the large pieces of material so it would end up as a rectangle shape and sewed the edges of the rectangle to keep its shape. I then sewed the two shorter edges together but left the center of the rectangle to form a loop . (You can shape your scrubs however you like, mine just happen to fold into square shapes.) I used a dark thread on the heavier grit scrubbers so that if the thread stained or became discolored, you wouldn’t see it as easily. I also used lighter thread just to see how much it would stain. I did this because I wanted to hang the scrubbing pads on the neck of my sink spout. This way, it can air dry and it has a place to be hung up when not in use. It will also drip into the sink when it is air drying. I know that this part of the design concept may not apply to everyone, but you can still hang it up wherever you want or hang it off of whatever you want in your sink area.
These can be hand washed and rinsed or thrown into the washing machine.

For my own use, this dish scrub has helped me solve my dish sponge/stainless steel wool pad/dish washing rag issue. My scrubs dry pretty fast so this design had worked out well for me. They seem to lather well and rinse off even faster. I actually enjoy hanging them on my sink’s spout neck because I know it’s the last step in the design of this product. I hope this post helps for those of you who would like an alternative to the dish scrubbing sponge issue.

T-Shirt Quilt Process

September 28, 2016August 12, 2018 / Yen-Van Tran / Leave a comment

09.28.2016

0800

Materials:

Old Comforter you want to use as the backing for the quilt
Enough t-shirts to cover the back of the comforter easily
Sewing machine

Tools:

Sewing machine

Not everyone in my family is big on donating items as quickly as I do. I don’t mind that, so I wanted to come up with a solution that would satisfy the use of the items but still make more room in the closet. In this case, the clothing item were the cotton t-shirt collections my family had accumulated. My older brother has a small collection of printed shirts from years of working for different companies or they were from different social events. I have kept a small collection for my mother over the years from elementary school t-shirts, to college t-shirts. I kept these because they marked a point in my life history that was significant. It bothered me that my t-shirts were stuffed into a bag in my old closet, so I wanted to make good use of them.

For both collections, I decided to make a t-shirt quilt for each family member. My brother’s shirts filled up one quilt and by combining my t-shirts as well as some of my mom’s, I would be able to create a single quilt for her. I found my brother’s old comforter which had The Transformers print on it and used that as the backing for his. I used my old comforter which had The Wuzzles print on it, for my mom’s quilt.

A few examples of t-shirt quilts that I’ve come across, suggest to cut out perfect squares in which the logo or image is centered in the middle of the square. I didn’t want to use this method because I didn’t want to waste any t-shirt material. I didn’t see the point in having perfect squares when the images varied so much on where they were located on each shirt. Also, I knew I could overlap the rows and create a slightly thicker quilt by leaving the extra material in place.

I decided to make this process in bullet form since a formal post would be too long to read, so here it goes:

Cut off all of the sleeves and collars from each shirt. Put aside the shirt sleeves which have logos printed on them because you will include them in the quilt later on as gap fillers. Keep your scraps when you make this project because you never know when you may need the extra material to fill in gaps.
Lay out the rows to see how you want the over all tile pattern to sit on the quilt and move them around if necessary. (I wanted each color shirt to create a checkered pattern with their base color)
Gather the sets of t-shirt rows and placed them on the blanket in the order from the top of the quilt, to bottom of the quilt. (You can take a picture before you move the tiles from the final layout on the blanket too)
Start pinning the t-shirts together with the shirts all facing upright and face to face. During this time, you may notice that come of the “t-shirt trimming” might be crooked, but that’s fine because that’s why you have the filler pieces.
Sew the tiles together in each row of shirts so that the rows become one piece.
Lay each row on the blanket as you want them to look and start pinning the rows to the blanket. Use as many sewing pins as necessary and be careful, because you may get pricked by those. Keep in mind that these pins may come apart once you move the blanket to the sewing machine, so you may want to pin the fabric together and give extra room on the pin for movement error.
For the areas that I saw were lacking in t-shirt fabric, I added in the t-shirt fillers. This usually happed around the edge of the blanket.
In order for me to fit the comforter into the sewing machine, I rolled it up on one side and sewed it through like this: (you my want to unravel it due to the weight of the blanket and that it may pull against the sewing machine as you feed it through)
Keep sewing, patient and you’ll finish. I sewed these tiles across the blanket. I have seen some people sew in a grid pattern along the tile edges. Since my tiles don’t line up exactly to the row above, I decided to only sew my tiles across the blanket.

This is a process and it takes time. There were a number of times when my sewing machine stitching backed up and I ended with a clump of thread on the backside of my quilt or when my needle broke twice. Just keep going and you’ll end up with the final product in no time. It’s an interesting project and you can put a spin on it however you like. This is a completely customized project which makes the intent that much more meaningful. I really am happy about how the blankets turned out and I know that my family is too.

Zero Waste Gifts

August 17, 2016August 12, 2018 / Yen-Van Tran / 1 Comment

08.17.2016

0800

I enjoy talking to people about the benefits of living a zero waste life. I enjoy it even more when they are also interested in transitioning to a zero waste life. When I do talk about this change, I like to help people jump-start their momentum into the routine of zero waste grocery shopping, so I usually gift jars with handmade produce bags. This is the reason why I sew so many, so I can give them away.

Talking about the lifestyle and the transition is a lot for one conversation. There a lot of areas in life to tackle and to hope that a stranger will pick up on all of the details in one conversation is unreasonable. This is why my gift of the handmade produce bags and jars specifically pertain to the grocery shopping task. It’s much easier to help them jump start their zero waste life with examples of what I use than to list a bunch of tasks to do- all at once. Tackling each area and room is going to be a big enough task, this is my way of easing them into the bulk grocery shopping.

And some people will not transition completely for a long time. Some may only be able to bulk grocery shop with certain items and may have to produce trash. This maybe due to medical reasons, physical location or perhaps resources aren’t available. Either way, a small change is still a change. As long as each person continues to move forward with their transition, it’s a point for the win column.

If you want some other Zero Waste Gift Options to get conversations started, check these out: