Sofa Armrest Organizer

October 14, 2019October 14, 2019 / Yen-Van Tran / Leave a comment

10.14.19

0600

Materials:

Two Curtains at 5′-10″ in length

Tools:

Sewing Machine
Sewing Kit

I have an extra set of curtains, which I didn’t want to use anymore. I decided to create a sofa armrest organizer with both curtain pieces. Both curtain pieces were 5 foot 10 in length, and 27 inches wide.

I wanted my sofa armrest organizer to sit at a certain height off the ground, but I also wanted the top half to also tuck underneath the couch cushion. I first measured how high off the ground I wanted my couch armrest organizer. Since I needed to hang it over the sofa armrest and then wrap back over the arm to tuck underneath the cushion, that left about 47 inches to tuck underneath the cushion.

I wanted to store books in the first organizer, which would be fairly heavy, so I needed a lot of the material to tuck under the seat cushion to hold it in place. I actually wanted the top part of the organizer to tuck underneath an entire sofa cushion width, due to the weight that would be applied.

FIRST SOFA ARMREST ORGANIZER:

When I measured out my first design, I wanted the pockets for my books to be 14 inches in height. I first hemmed all of the edges and then I folded one edge to create the 14″ tall pockets. I sewed around the edge of the folded piece (yellow arrows) and then divided the pocket in half, and sewed a dividing line down the center to create two tall pockets (red arrow). These pockets will be able to hold my books and paperwork that I’m currently working on. I wanted my pockets to be a bit taller than the standard paper size (8.5″ x 11″), due to the fact that I knew the width of the pocket might eat up some of the height. I also wanted to be able to hide my books and paperwork, so my pockets wouldn’t look like they were overflowing with paper.

To attach the sofa armrest organizer, I removed the couch cushion on the side of the couch, located how high I wanted to hang the organizer, and then replaced the couch cushion. Since the top half of the fabric organizer is tucked under the couch cushion, it stayed in place.

SECOND SOFA ARMREST ORGANIZER:

I also wanted to create a second design, which would have smaller pockets for smaller items. My second design would have 10 inches in height for the books, and 6 inches for smaller objects.

Using the same sewing method as the first design, I hemmed all of the edges of the fabric material, and then measured 16″ of material at one end. I folded up the 16″ material, sewed along the outside edges of the tall pocket (yellow arrows), which created a giant 16″ tall pocket.

I then took the bottom 6″ of the pocket and folded it up, to create a shorter 6″ pocket at the bottom. This 6″ tall pocket also helped create the 10″ pocket behind the smaller pockets. I then sewed on both of the side edges of the fabric piece (red arrows) and then sewed a dividing line (blue arrow) to create a total of four pockets for this design. I sewed the edges of this design, all the way to the top of the pocket to reinforce the side edges.

Using the same method as the first sofa armrest organizer, I located where I wanted the organizer to hang on my armrest and I tucked the top half of it under the couch cushion on the end.

Since these sofa armchair organizers are made of fabric material, I can toss them into the washing machine and wash them easily. I can also fold them up and put them away if I don’t need to use them. Fabric is my favorite material to work with since it can be taken apart and reused multiple times. I love that it is a very flexible medium and I was able to put my old curtains to good use.

Upcycling A Shoe Organizer

October 2, 2018October 2, 2018 / Yen-Van Tran / Leave a comment

10.02.2018

0600

Materials:

One over the door shoe organizer
X-acto blade
Cutting mat (or cardboard, plywood, some type of surface you’re willing to cut into and can damage just a little bit)
4 Safety Pins

Tools:

Sewing machine
Sewing Kit

So I’ve owned an over the door shoe organizer for awhile. I didn’t use it a lot because I didn’t have many pairs of shoes. When I started to declutter my life and minimize my possessions, I kept it because I still liked the design and I knew I could use the material to create something else.

Because I’m not a fan of keeping items out in the open, much less hanging them out in the open, I knew I wanted to upcycle this shoe organizer into smaller organizers. I personally like things to be put away. My minimalist, zero waste lifestyle lends my living space towards clean surfaces and minimal decor. So I wanted to create two smaller organizers which could be hung up in the closets.

The goal was to create two separate organizers that were each 2 pockets across by 3 pockets vertically on each side of the smaller organizer. So each side of the hanger would hold a grid of pockets that was 2 pockets across by 3 pockets vertical.

First I cut the shoe organizer in half.

I then folded each organizer in half (vertically) to find out where I wanted to locate the hangers.

I then placed each hanger on each organizer, as I wanted them to sit. I wanted to place each hanger so that the top bars of the hangers would still be protected by the fabric. I only wanted the neck of the hanger to stick up and out of the fabric so the fabric organizer would sit higher on the hanger. The hanger would have more control of the overall weight of the items inside each pocket when it was hung up.

I placed the hangers where I wanted each hanger to be located on each organizer and then marked the location of the bottom bar. I needed to make a mark at those locations, because that’s where the bottom of the openings for the hangers would pass through.

Using the X-acto blade, on the folded edge, I carefully cut a straight line of where the hanger would stick out. I cut along the mid line of the fabric grid pattern and only cut enough for the hanger to fit. You can sew the edges of these openings if you want a clean and sturdy structure around the edge of the opening. I suggest using a running stitch to do that, if you choose to.

Using the bottom of opening as a location marker, I sewed both sides of each organizer together. I wanted the backs folded and sewed to one another to create a more sturdy central structure. I sewed from the bottom of each opening, around and up to the other side, making sure I stopped at the other marker.

The idea was that I wanted to seal the two flaps of pockets to each other, but leave enough room for the hanger to slide in and out of the design.

Once the hanger is slid into place, the flap should allow the user to remove the hanger if necessary. I used a hem stitch to secure the top of the opening on the folded edge (see below). I did this because I know that the weight of the the organizer will tear the opening over time. I wanted to secure the top of the opening and reinforce the structure.

I stitched an extra line above the hanger (towards the folded side of each hanger), but underneath the pocket flaps, to reinforce extra support for the organizer.

Using a safety pin, I pinned the opened edge approximately where the top of the hanger was located on the opposite side. This way, the hanger can be removed easily when it comes time to wash it or put it away. The safety pin will act as a closing mechanism to hold the hanger in place.

So there you have it, this is how I upcycled my over the door shoe organizer. Although, I technically only created smaller shoe organizers, I had the idea that I could use these smaller organizer to store smaller items such as jewelry, scarfs, socks, etc., that can get lost in a closet. Basically, anything you might store in the top drawer of your dresser, you might use this for. I don’t use a dresser, so this product can be useful for me. Right now I actually use a few of the pockets to keep some running and workout items organized. I like this design for the fact that it’s double sided and it can be folded up and put away if it’s not being used. Hopefully this post might spark some organizational ideas for your life.

Until next time!

Backpack Hacks

August 15, 2017April 26, 2020 / Yen-Van Tran / 4 Comments

08.15.2017

0600

With all of my backpacks that I have ever owned, I hack them the exact same way as I always have. Going back as far as middle school, I always had to hack my backpacks. It was my way of customizing my carrier to my exact needs and over time I would edit it as my needs changed. Within each compartment I always created some type of hanging or attachment mechanism to hang my water bottles, extra bags within the compartments or hang something I needed access to immediately. most of the time I hung items that I needed access to so that those items weren’t at the bottom of my bag, where I had to go digging around to look for them.

Front of the backpack

I always attach extra reflectors so that in low light, vehicles or any type of light can bounce off of my backpack and I can be visible. These reflecting straps are for bikers, but I took two of the straps and weaved them through my exisitng strap set up.

For all of my zippers that open to significant compartments, I always sew a section of the zipper, so it limits the access to that compartment to only one direction of movement for the zipper. I prefer to only have access in one direction for the zipper movement so it’s easier to watch over and maintain. I also attach metal rings right below the point of the sewing block (through the exposed zipper tape) so that I can use this ring to lock my carabiners from the outside but to also hang items on the inside of the bag.

On the inside, I hook extra interior metal rings with carabiners to the exterior rings that are popping through the tape so I can hang items on the inside. I’ll hang my water bottle from these interior rings (when my external water bottle pocket has my coffee tumbler in it) or small bags so I can keep items separated in the same compartment. These interior rings are there for anything that needs to be hanged or utilized.

Sides of the backpack

I also sew blocking for my smaller compartments and create a locking system for these pockets as well. For the smaller pockets, it really just depends how and where you want to secure the pocket. I chose to insert an extra ring so that I could attach an extra carabiner to it and lock the zipper with it.

For my external water bottle pocket, I usually take one of the extra backpack straps (that I trimmed off) to create a safety strap for the external water bottle pocket so that it can hold taller water bottles more securely. There have been a few incidents where my external water bottle pocket wasn’t deep enough and due to the fact that I had so much stuff in my backpack, my water bottle managed to get squeezed out of the pocket.

Back of the backpack

I usually trim the extra strap slack that comes with the backpack straps. I don’t like any loose hanging straps so I will measure how high I want to carry my backpack and trip, then hem the straps accordingly.
For my backpack straps, I like to keep my smaller items very close to me. So I will attach some type of pocket (large enough to fit my “wallet” items and my cell phone) to the front. This backpack didn’t come with a pocket for those types of intimate items.

I also ALWAYS, ALWAYS attach an extra carabiner to the other strap, so I can hook my keys onto my strap quickly.

So there you have it, those are the hacks I made for this backpack. This is my day to day back pack, so I’ll run to the store or go hiking with it. I do have another hiking backpack that’s a 65 gallon capacity for traveling and I’ve hacked that accordingly as well. Hopefully you may see a hack i described here that you would like to use on your own backpacks or carrying bags that you may want to use.

Created Slim Hanging Organizers

August 1, 2017August 15, 2018 / Yen-Van Tran / Leave a comment

08.01.2017

0600

Materials:

Three 7 inch-8 centimeter, white zippers (for one pillowcase design)
Two 12 inch, pink zippers (for the second pillowcase design)
Two Velvet Hangers

Tools:

Sewing Machine or sew by hand

I always try to take up less space than necessary when it comes to my home. It’s not that I dont’ have the room to spread out, but I personally don’t think it’s necessary. I don’t like my items and possessions spread out over a large space because it takes more energy to find things and living a more compact lifestyle helps me keep my possessions to a minimum. As a designer, it’s an interesting challenge to minimize the space that I take up.

So I decided to create a slim organizer for my closet. I had a hanging closet shelf but I wanted to get rid of it. In order to get rid of it, I still needed some type of organizer in its place. The items that I needed to organize were small clothing items as well as small accessories. This slim organizer only needed to hold the weight of those items. I did move some stuff out of the original hanging shelf to other areas of the house, so what you see in the images below isn’t a direct transfer of items to the new slim organizer.

Hanging organizers actually already do exist in stores, but from what I’ve seen, these organizers tend to have the user access the pockets from the front of the organizer. It would be easier for a person who has a walk-in closet to use those organizers, but I wanted to make a slim organizer which I could access from the side.

So in the end, this organizer helped me reduce my space by half:

Here is what I did…

I gathered my pillowcases and designated one of the pillowcases to be divided into three sections and the other pillowcase would be divided into two sections.

I took one pillowcase and hemmed the open end of the pillowcase. I then folded the pillow case into thirds and marked the lines using sewing pins. This pillowcase would have the three 7 inch-8 centimeter, white zippers sewed to it.

I sewed along the lines to close off the three separate sections, then I placed my zippers down to mark the location of the zippers. Depending on how I wanted to access my slim organizer in the closet, I had to choose which side of the pillowcase to attach the zippers. Since I wanted this slim organizer to be on the right side of my closet, I wanted the openings on the right side of the pillowcase so that when it was hanging up, I could access the slots easier. I also left about an inch margin between the zipper and the edge of the pillowcase because the items inside will create a bulge that I had to take into consideration.

I used an ink pen to make tiny dots at each end of the zipper. I actually marked the dots in between the zipper teeth at each end, this way, it also centered the location of the zipper. I connected each set of dots to create the cut lines in order to fit my zippers into the pillowcase. I just used scissors to cut these lines.

After I cut the lines, I inserted the hanger into the opening that was on the end of the pillowcase that was originally closed. I folded the pillowcase in half (vertically) to find the center and pretty much wedged the metal hook through the pillowcase. I chose to place my hanger on the original closed end of the pillowcase because if I used the hemmed end of the pillowcase for the hanger, the weight of the items in the organizer might weaken the that end of the pillowcase over time. I had to consider the weight of each pocket that was created, so I constantly thought about the overall weight that would pull on the material itself.

Once I placed my zippers into each slot that was made, I folded the edges of the pillowcase down to the zippers and pinned them together with sewing pins. Then I hand sewed the zippers to the pillowcase (making sure I sewed both the hemmed layer and the top layer of the pillowcase to the zipper).

Once I was done, I used the same process to create the double pocket slim organizer. The triple pocket slim hanging organizer will be used for small items and the double pocket slim organizer will be used for some extra pieces of clothing items.

I don’t know if this is a favored design, but I personally like how much less space it takes up. this design works for me and, my space. Hopefully this design may jog some space organizing ideas for you as well.

Make-Up Brush Bag Hack

May 9, 2017August 14, 2018 / Yen-Van Tran / Leave a comment

05.09.2017

0700

Materials:

Plastic store bought brush bag

Tools:

Razor Blade or scissors (Please be careful when using the razor blade)

So I bought an e.l.f. Angled Blush Brush from Target back in 2016 and it came in a clear plastic bag such as the ones in the pictured below. I didn’t want to add it to my trash collection, so I set out on trying to figure out how to convert it into a product that would be useful in mylife.

I knew I wanted to create a holder for all of my brushes (luckily I only use two types of brushes) So I came up with this design to hold my vertical make up tools, such as my mascara, eyeliner pencil, angled blush brush and my EcoTools, Bamboo Smudge Eyeliner Brush.

I sewed the flap that covered the holder to the bag itself. I did this because, I didn’t want to remove the flap to access a clean opening but to also reinforce the bottom of the holder. (At this point I had decided to hang this object as a vertical brush holder).

I opened the other end of the holder by cutting a small slit across the top side of the bag and hold punched a hole on the opposite side. I only put one hole punch on one side because I would be using that side to hang the bag and I didn’t want anything blocking the opening of the bag. Lets call the hole punch end the “Top” and the sewed end of the bag, the “Bottom”. (you kinda have to picture this bag vertically hanging like that)

I used a permanent marker to show you where I placed my cuts on each side of the bag. On the same side as the hold punched hole, I sliced a longer slit on the bottom third of the bag. On the opposite side of the bag, I sliced a shorter cut closer to the top. These cuts do not cut through both walls, please keep that in mind. This design will only work if both walls of the holder are not cut at the same spot.

For the taller brushes, I am able to insert both of my brushes through the opening at the top, however, I can also slide the brush I tend to use through the slit towards the top.

The same rule applies for the slit towards the bottom third of the bag. I can use the slit I had created to hold my mascara and eyeliner but be able to access them from the outside. The next few images demonstrate the versatility of the cuts better than how I’m describing them.

Here is what the bag looks like when it’s hanging up and being utilized. You can see that my EcoTools, Bamboo Smudge Eyeliner Brush is inserted through the opening I had created (towards the top of the bag) and that my angled blush brush is actually on the inside of the bag. I use my Eyeliner brush more than my angled brush so this is why I keep it on the outside, for easy access. On the opposite side of the bag, you can see my small eyeliner and mascara sticking out from the small opening I had created towards the bottom. I also use my mascara and eyeliner often so I like to have access to them easily.

When I travel or move around with my makeup brushes, I can easily tuck everything inside the bag and nothing with get caught during transportation. I actually do have a bag for my toiletries when I travel and this brush holder goes into that bag as well. The last image shows what the brush holder looks like once everything is tucked inside the entire bag. I know that this bag with eventually fall apart and I will end up adding it to my trash pile, but as long as I don’t stretch the plastic by putting too many items into this holder, it might hold up well.

This is a simple and interesting design manipulation of what we receive along with products we buy and how to re-design them to accommodate to our own needs. I really like this design manipulation because I tend to hang things a lot and I didn’t have to throw any packaging away. I hang things a lot because I like to keep my surfaces clean. Maybe this design might accommodate you somehow, I hope it will.

Hanging Boots

July 6, 2016August 12, 2018 / Yen-Van Tran / Leave a comment

07.06.2016

0800

Materials:

Velcro straps
Metals rings
Binder clips
Carabiners

So there are a few ways I organize my boots. Over the years, I’ve played around with different set ups of how to hang boots. If you’ve read my blog, you might have read that I hate having items on the floor, I just don’t like clutter on my floor.

For those who own tall boots, you’ll know the issue of your boots folding over when they’re standing upright. I deal with this issue by hanging them up.Using my current pant rack in my closet system, I clip large binder clips to join the sets of boots together and then I’ll attach a metal ring to the binder clip. With this method, I attached the rings to a carabiner that hangs from one of the pant racks. I also tried splitting up the pairs of boots to hang from separate carabiners too.

The metal carabiners were slipping easily from the pant racks so I switched out the carabiners with velcro straps. The velcro straps created more friction so the boots stayed in place easier.

Another method I tried to use was to hang the boots from my existing shelf. I screwed a few screws to the interior of the lip of the shelf and hung the boots from there. If you own a metal over-the-door-shoe rack, the boots can also be hung from there with this technique.

With the idea of hanging boots using adjustable Velcro, you can pretty much hang sets of boots anywhere. the idea is to keep them organized and not loose their shape so that you can continue to extend their lives. This is how I organize my boots, maybe it’ll help you as well.