Upcycling A Shoe Organizer

10.02.2018

0600

Materials:

  • One over the door shoe organizer
  • X-acto blade
  • Cutting mat (or cardboard, plywood, some type of surface you’re willing to cut into and can damage just a little bit)
  • 4 Safety Pins

Tools:

  • Sewing machine
  • Sewing Kit

 

DSC_0326

So I’ve owned an over the door shoe organizer for awhile. I didn’t use it a lot because I didn’t have many pairs of shoes. When I started to declutter my life and minimize my possessions, I kept it because I still liked the design and I knew I could use the material to create something else.

Because I’m not a fan of keeping items out in the open, much less hanging them out in the open, I knew I wanted to upcycle this shoe organizer into smaller organizers. I personally like things to be put away. My minimalist, zero waste lifestyle lends my living space towards clean surfaces and minimal decor. So I wanted to create two smaller organizers which could be hung up in the closets.

The goal was to create two separate organizers that were each 2 pockets across by 3 pockets vertically on each side of the smaller organizer. So each side of the hanger would hold a grid of pockets that was 2 pockets across by 3 pockets vertical.

First I cut the shoe organizer in half.

DSC_0270-2_Shoe Organizer Diagram

 

I then folded each organizer in half (vertically) to find out where I wanted to locate the hangers.

DSC_0272-2

I then placed each hanger on each organizer, as I wanted them to sit. I wanted to place each hanger so that the top bars of the hangers would still be protected by the fabric. I only wanted the neck of the hanger to stick up and out of the fabric so the fabric organizer would sit higher on the hanger. The hanger would have more control of the overall weight of the items inside each pocket when it was hung up.

DSC_0275-2

I placed the hangers where I wanted each hanger to be located on each organizer and then marked the location of the bottom bar. I needed to make a mark at those locations, because that’s where the bottom of the openings for the hangers would pass through.

DSC_0273-2

Using the X-acto blade, on the folded edge, I carefully cut a straight line of where the hanger would stick out. I cut along the mid line of the fabric grid pattern and only cut enough for the hanger to fit. You can sew the edges of these openings if you want a clean and sturdy structure around the edge of the opening. I suggest using a running stitch to do that, if you choose to.

Types of Stiches

DSC_0279-2DSC_0277-2

Using the bottom of opening as a location marker, I sewed both sides of each organizer together. I wanted the backs folded and sewed to one another to create a more sturdy central structure. I sewed from the bottom of each opening, around and up to the other side, making sure I stopped at the other marker.

DSC_0276-2 - Copy

The idea was that I wanted to seal the two flaps of pockets to each other, but leave enough room for the hanger to slide in and out of the design.

DSC_0282

Once the hanger is slid into place, the flap should allow the user to remove the hanger if necessary. I used a hem stitch to secure the top of the opening on the folded edge (see below). I did this because I know that the weight of the the organizer will tear the opening over time. I wanted to secure the top of the opening and reinforce the structure.

DSC_0313-2

I stitched an extra line above the hanger (towards the folded side of each hanger), but underneath the pocket flaps, to reinforce extra support for the organizer.

Using a safety pin, I pinned the opened edge approximately where the top of the hanger was located on the opposite side. This way, the hanger can be removed easily when it comes time to wash it or put it away. The safety pin will act as a closing mechanism to hold the hanger in place.

 

DSC_0314-2DSC_0320-2

So there you have it, this is how I upcycled my over the door shoe organizer. Although, I technically only created smaller shoe organizers, I had the idea that I could use these smaller organizer to store smaller items such as jewelry, scarfs, socks, etc., that can get lost in a closet. Basically, anything you might store in the top drawer of your dresser, you might use this for. I don’t use a dresser, so this product can be useful for me. Right now I actually use a few of the pockets to keep some running and workout items organized. I like this design for the fact that it’s double sided and it can be folded up and put away if it’s not being used. Hopefully this post might spark some organizational ideas for your life.

Until next time!

DSC_0329

 

 

 

Created Slim Hanging Organizers

08.01.2017

0600

Materials:

  • Three 7 inch-8 centimeter, white zippers (for one pillowcase design)
  • Two 12 inch, pink zippers (for the second pillowcase design)
  • Two Velvet Hangers

Tools:

  • Sewing Machine or sew by hand

I always try to take up less space than necessary when it comes to my home. It’s not that I dont’ have the room to spread out, but I personally don’t think it’s necessary. I don’t like my items and possessions spread out over a large space because it takes more energy to find things and living a more compact lifestyle helps me keep my possessions to a minimum. As a designer, it’s an interesting challenge to minimize the space that I take up.

So I decided to create a slim organizer for my closet. I had a hanging closet shelf but I wanted to get rid of it. In order to get rid of it, I still needed some type of organizer in its place. The items that I needed to organize were small clothing items as well as small accessories. This slim organizer only needed to hold the weight of those items. I did move some stuff out of the original hanging shelf to other areas of the house, so what you see in the images below isn’t a direct transfer of items to the new slim organizer.

Hanging organizers actually already do exist in stores, but from what I’ve seen, these organizers tend to have the user access the pockets from the front of the organizer. It would be easier for a person who has a walk-in closet to use those organizers, but I wanted to make a slim organizer which I could access from the side.

So in the end, this organizer helped me reduce my space by half:

dsc_48972017-07-25

Here is what I did…

DSC_6000

I gathered my pillowcases and designated one of the pillowcases to be divided into three sections and the other pillowcase would be divided into two sections.

I took one pillowcase and hemmed the open end of the pillowcase. I then folded the pillow case into thirds and marked the lines using sewing pins. This pillowcase would have theย three 7 inch-8 centimeter, white zippers sewed to it.

 

DSC_6008 - Copy

I sewed along the lines to close off the three separate sections, then I placed my zippers down to mark the location of the zippers. Depending on how I wanted to access my slim organizer in the closet, I had to choose which side of the pillowcase to attach the zippers. Since I wanted this slim organizer to be on the right side of my closet, I wanted the openings on the right side of the pillowcase so that when it was hanging up, I could access the slots easier. I also left about an inch margin between the zipper and the edge of the pillowcase because the items inside will create a bulge that I had to take into consideration.

I used an ink pen to make tiny dots at each end of the zipper. I actually marked the dots in between the zipper teeth at each end, this way, it also centered the location of the zipper. I connected each set of dots to create the cut lines in order to fit my zippers into the pillowcase. I just used scissors to cut these lines.

 

DSC_6046DSC_6050

DSC_6009- Copy

After I cut the lines, I inserted the hanger into the opening that was on the end of the pillowcase that was originally closed. I folded the pillowcase in half (vertically) to find the center and pretty much wedged the metal hook through the pillowcase. I chose to place my hanger on the original closed end of the pillowcase because if I used the hemmed end of the pillowcase for the hanger, the weight of the items in the organizer might weaken the that end of the pillowcase over time. I had to consider the weight of each pocket that was created, so I constantly thought about the overall weight that would pull on the material itself.

Once I placed my zippers into each slot that was made, I folded the edges of the pillowcase down to the zippers andย pinned them together with sewing pins. Then I hand sewed the zippers to the pillowcase (making sure I sewed both the hemmed layer and the top layer of the pillowcase to the zipper).

DSC_6016

DSC_6021.JPG

Once I was done, I used the same process to create the double pocket slim organizer. The triple pocket slim hanging organizer will be used for small items and the double pocket slim organizer will be used for some extra pieces of clothing items.

I don’t know if this is a favored design, but I personally like how much less space it takes up. this design works for me and, my space. Hopefully this design may jog some space organizing ideas for you as well.

DSC_6028

DSC_6052

DSC_60622017-07-25