hook

01.09.2018

0600

Materials:

Wood board (18 inches long x 5 inches wide 1-1/2 inches deep)
Four 3 inch wood screws
Ten 1-1/2 inch wood screws
5 Spoons

Tools:

Power Drill
Power Screwdriver
Needle Nose Pliers
Slip Joint Pliers
Safety glasses
Gloves

So I wanted to make a coat hanger but I didn’t want to buy one. Apparently I had materials at home to make one of my own. This project is a fairly easy DIY for any of you who are curious.

My board was 18 inches wide and I wanted a minimum of 1 inch on each side, for margins. This left me with 16″ to work with. So initially I wanted to use 7 spoons for the hangers, but after I measured the distance, I decided to only use 5 spoons.

I divided the board up into three sections. The height of my board was 5-1/2″, but if you don’t want to use numbers, simply take a piece of paper and fold it into thirds. Then with a pencil, mark the first line and then the second. I wanted to offset my rows of spoons so the red line is for the top row of spoons and the green line is for the center of the bottom row of spoons.

Where the red line and margins intersect is where I drilled my top mounting holes. My bottom mounting holes is where the green line and the margins intersect. These holes are marked by the yellow circles in the image.

For the spoons, I wanted to drill 2 holes to mount each spoon and I knew I had to create hooks by manipulating the spoons. I picked out a drill bit that was a similar size diameter of my screws I was going to use on the spoons. Usually I choose a drill bit smaller than my screw, but that working with wood only. When working with metal, you want a drill bit that the same size as the screw since metal won’t give. Also, if you don’t choose a drill bit smaller than your screw, there’s a good chance you’ll strip the screw’s threads as you drill.

The green line marks the point of where I wanted my spoons to bend upwards, so they could be used as hooks.

When I drilled the holes, I wore gloves and my safety glasses because the metal slivers would fly off of the power drill. I applied slow but steady pressure while holding the spoon still and then I dumped the metal shavings into one side of my purple container. I did this to contain the shavings but also because it would be easier to discard them after I finished.

I first started bending the spoons by using the edge of my step ladder, then I used my Slip Joint Pliers to hold the spoon while using the Needle Nose Pliers to bend the spoons into hooks.

Once all of the spoons had holes drilled into them, I spaced the spons apart from each other in three inch increments. I proceed to attach the spoons to the board. For the wall mount attachment holes, I sunk the holes into the wood so that there was a slight design detail. I initial had made 2 drill holes so that I could mount it to the stud in the wall (those are the extra holes you see floating on the left half of the board), but I changed my mind and decided to directly attach it to the drywall instead. Because I was planning to use three inch screws, I knew that mounting it to the drywall wouldn’t be a problem.

But because I changed my mind on which drill holes I wanted to use to mount the coat rack, I now had two random holes that looked out of place. To fix this, I mirrored the holes to the other side of the board and then filled in the extra holes will extra wood filler we had left over.

I centered my coat rack and attached it to my wall. As you can see, the mistake holes look like design elements with the wood filler.

So there it is, my coat rack made from spoons. These spoons are a few extra spare spoons from my mother’s kitchen and I really like that I was able to upcycle these extra spoons, knowing that a part of her kitchen was now used in an item I really needed. It’s a nice homage to my mom in a subtle way.

Our homes and possessions hold a great deal of different types of materials in which we can reuse and upcycle into new items. Once you breakdown how different types of materials are used, the possibilities are endless. Scan your home and surroundings, I’m sure you’ll find a lot of resources.

08.15.2017

0600

With all of my backpacks that I have ever owned, I hack them the exact same way as I always have. Going back as far as middle school, I always had to hack my backpacks. It was my way of customizing my carrier to my exact needs and over time I would edit it as my needs changed. Within each compartment I always created some type of hanging or attachment mechanism to hang my water bottles, extra bags within the compartments or hang something I needed access to immediately. most of the time I hung items that I needed access to so that those items weren’t at the bottom of my bag, where I had to go digging around to look for them.

Front of the backpack

I always attach extra reflectors so that in low light, vehicles or any type of light can bounce off of my backpack and I can be visible. These reflecting straps are for bikers, but I took two of the straps and weaved them through my exisitng strap set up.

For all of my zippers that open to significant compartments, I always sew a section of the zipper, so it limits the access to that compartment to only one direction of movement for the zipper. I prefer to only have access in one direction for the zipper movement so it’s easier to watch over and maintain. I also attach metal rings right below the point of the sewing block (through the exposed zipper tape) so that I can use this ring to lock my carabiners from the outside but to also hang items on the inside of the bag.

On the inside, I hook extra interior metal rings with carabiners to the exterior rings that are popping through the tape so I can hang items on the inside. I’ll hang my water bottle from these interior rings (when my external water bottle pocket has my coffee tumbler in it) or small bags so I can keep items separated in the same compartment. These interior rings are there for anything that needs to be hanged or utilized.

Sides of the backpack

I also sew blocking for my smaller compartments and create a locking system for these pockets as well. For the smaller pockets, it really just depends how and where you want to secure the pocket. I chose to insert an extra ring so that I could attach an extra carabiner to it and lock the zipper with it.

For my external water bottle pocket, I usually take one of the extra backpack straps (that I trimmed off) to create a safety strap for the external water bottle pocket so that it can hold taller water bottles more securely. There have been a few incidents where my external water bottle pocket wasn’t deep enough and due to the fact that I had so much stuff in my backpack, my water bottle managed to get squeezed out of the pocket.

Back of the backpack

I usually trim the extra strap slack that comes with the backpack straps. I don’t like any loose hanging straps so I will measure how high I want to carry my backpack and trip, then hem the straps accordingly.
For my backpack straps, I like to keep my smaller items very close to me. So I will attach some type of pocket (large enough to fit my “wallet” items and my cell phone) to the front. This backpack didn’t come with a pocket for those types of intimate items.

I also ALWAYS, ALWAYS attach an extra carabiner to the other strap, so I can hook my keys onto my strap quickly.

So there you have it, those are the hacks I made for this backpack. This is my day to day back pack, so I’ll run to the store or go hiking with it. I do have another hiking backpack that’s a 65 gallon capacity for traveling and I’ve hacked that accordingly as well. Hopefully you may see a hack i described here that you would like to use on your own backpacks or carrying bags that you may want to use.