DIY Makeup Wrap

December 23, 2019December 22, 2019 / Yen-Van Tran / Leave a comment

12.23.19

0600

Materials:

Fabric piece – 28″ x 17″
Ribbon – 38″ long

Tools:

Sewing Kit
Sewing Machine
Ruler
Blue Ink pen (if using a dark fabric) OR Washable crayon

So I wanted some type of organizer for my makeup and my makeup brushes. A lot of the organizers that I found in stores, only organize make up brushes, but I wanted an organizer that I could also organize my makeup pallets as well. I just wanted some type of organizer that could organize multiple beauty products. Since I couldn’t find one, I decided to make it.

I found two pieces of black fabric that’s were 17″X28″. Both pieces of fabric are a cotton blend and are usually used to make dress pants. I knew the fabric would be durable for this project.

First, I hemmed all the edges. Since I hemmed all the edges at 1/2″ in width, and I folded each edge over twice, the final size of the fabric piece was 15″x26″. Essentially, I had used up an inch of fabric on each side.

My makeup brushes averaged a height of 7.5″, so I knew that my makeup wrap would ideally be 8″ high.

I decided that I wanted 4.5″ base, to hold all of the items in place. I folded the bottom of the wrap, up 4.5″ and pinned the fabric together using sewing pins. I then folded my wrap in half, to find the center line. I wanted the right side of the wrap to hold my brushes and the left side of my wrap to hold my makeup palettes, combs, mascara, eyeliner, etc. I wanted my wrap to be able to hold more than just make up brushes.

Using a washable white crayon, I marked off 1″ sections, for my brushes and then divided the other half into two 3″ sections and two 3.5″ sections. Three inches seemed like a good width for makeup palettes, but check the width of your palettes to see if you need a wider section. I wanted the last two sections on the left side to be 3.5″, because I have a feeling that I’ll need slightly larger slots in the future.

In addition to the washable crayon, I also used a blue ink pen to draw guide lines for the slots, so I could sew the lines straight, when using my sewing machine. The blue ink blends in with the black fabric, so it was only visible under the sewing machine light bulb. I also could have used the washable crayon to mark off the guide lines as well.

Usually, when I create any sewing project, I try to end the sewing line, close to the edge of the fabric. It’s easier to create the back stitch when it’s close to the edge of the fabric.

In this case, I started my sewing line near the top of the folded flap, used the back stitch lever to create a back stitch, continued to sew down the guild line, and then ended the line at the bottom edge, with another back stitch as well.

Since the wrap was long, I folded the right side of the wrap inward, so I could still keep the shape of the wrap neat and clean as I fed the fabric through the presser foot and needle of the machine.

I wanted all of the sewing lines to start at the hem line, because I thought it would create a cleaner look for the wrap.

After I finished sewing all of the slot lines, I wanted to create a top flap, that would cover the makeup bristles and ferrules. I simply folded the top edge of my wrap down 3″, and ironed that edge.

I took my ribbon, and I folded it in half. I needed to find the center line of the ribbon, so I can line up with the center line of the last slot on the left side. I wanted my makeup brush wrap to unroll to the right, so I had to attach the ribbon on the left back side. The wide slots on the left also provide a good section to attach the ribbon to.

The location of where I sewed the ribbon was based on the location of the heels of my brushes. The heels of my brushes were close to the middle of the wrap. It was also the location where my ribbon had to wrap around in order to contain the entire wrap securely.

Using a sewing pin, I pinned the ribbon to the wrap, and sewed the ribbon to the back of the last left slot. I wanted a really long ribbon for this makeup brush wrap, because I wanted to be able to wrap the ribbon twice around the entire wrap, if needed.

So this is what the finished product ended up looking like. The bottom picture is what the wrap looks like when it is wrapped up.

DIY Thumb Loops In Sweater Sleeves

November 18, 2019November 25, 2019 / Yen-Van Tran / Leave a comment

11.18.2019

0600

So this blog post is a personal life hack of mine. When I work out, I like to wear sweaters. Now, these sweaters are not always athletic sweaters, but simple sweaters that I buy just to wear on a day-to-day basis. I like to go running in these sweaters because they’re comfortable and warm. However, when I go running with these sweaters, the sleeves tend to run up my arm. I prefer the sweaters to cover my wrist and not bunch up when I’m running. I like the running sweaters that are designed with thumb loops, but they tend to be more expensive as well. Since I love my sweaters that I wear day to day, I decided to create my own thumb loops for my sweaters.

It’s a very simple process to create these thumb loops. First, I laid down my sweater where the sleeve lay flat on the table. I located the center line of the sleeve, and then chose to locate my thumb loop on the bottom half of the sleeve, but on the cuff of the sleeve. I found the center line of the bottom half of the sleeve, and I decided to locate my new thumb loop there.

When I wear my sweaters, my hand falls naturally to my side, in which my thumb faces towards the front of my body. This is why I located the thumb loop on the bottom half of the sleeve.

I wanted my thumb loop to be 1 inch in length and about half an inch from the bottom of the sleeve cuff. Using scissors, I cut a small slit that was 1 inch in length.

For my right sleeve, I used the same process as I did with the left sleeve. I located the center line of the right sleeve, and then located the center of the bottom half of the sleeve. I cut a one inch slit that was half an inch away from the bottom of the sleeve cuff.

I removed my extension table in order for the sleeve to fit underneath the presser foot of the machine. I slid the left cuff over the needle plate and started to sew the edge of the thumb loop. I used a tight zigzag stitch, so the fabric would hold up during washes and use. Since I knew that these thumb loops would go through a bit of wear and tear, I used the back stitch lever to create a strong and permanent attachment at the ends of the thumb loops.

The back stitch lever created the heavy and thicker starting points and end points of the outline of the thumb loops.

I flipped my left sleeve inside out, and continued to outline the other side of this thumb loop. I used the zigzag stitch again and used the back stitch lever so both ends of the opening would have an even reinforcement, of the thumb loop.

When I turned my sweater inside out, the thumb loops were finally finished being created. I use this hack on both of my sweaters, so now the sleeves won’t run up my arms when I workout.

This is a really simple hack for an issue that I dealt with on a daily basis. Although I know my thumbs will stick outside of my sleeves, when I run,they don’t get too cold. Sometimes I will run with my running gloves when the weather drops too low, so technically, my hands are still warm. Some people prefer to not have the thumb loops, but I like to keep my wrists covered when I run. This hack took less than 30 minutes to create and finish, so it didn’t take much time out of my day at all. I hope this hack will inspire other hacks that you might be needing in your life.

Quick T-Shirt Pocket

September 11, 2018September 26, 2018 / Yen-Van Tran / Leave a comment

09.07.2018

0600

Materials:

One T-shirt (or two, but definitely at least one)

Tools:

Sewing machine
Sewing Kit

Living a Zero Waste life means that I create simple solutions for simple problems since I don’t want to go buy anything new or seek out another possession to take care of.

So I usually carry my phone around with me when I’m doing certain types of household tasks. These tasks don’t require a lot of vigorous movement, but I’m definitely moving around. A lot of the time it’s annoying to remember to carry the phone from one place to another when I’m running around the house and if my hands are dirty, I really don’t want to touch my phone. I needed a quick solution where I could carry the phone along with my keys without much hassle. I didn’t want to go out and buy a separate cell phone holder strap that would wrap around my arm. I have one for workouts, and that strap holds down my cell phone securely since I’m running. But I just needed a quick solution where I could carry around my phone and my keys easily for a few hours.

My quick solution was to see my t-shirt sleeve in half and create a pocket. my t-shirt sleeves are usually longer than I need them to be. This gave me the extra material to work with. I simply folded my sleeve in half and pinned the sleeve all the way around.

Depending on the width of your cell phone, measure that distance out on the top of the sleeve. Just make sure you divide the width of your phone in half and center the opening on the top of the sleeve.

For the other sleeve, I made the opening just about the same size since I knew I was going to use the other pocket for keys or my credit card.

Then just sew the sleeve from the front to the back or back to the front, making sure you still leave enough room for your cell phone. Then tie off the open thread ends.

If you put smaller items in the short pockets, they tend to fall towards the bottom of the sleeve. This can be annoying for some but for me it gives me a sense of security knowing my items won’t fall out. I just need to go fishing for my keys at the end of the day.

So there you have it. My quick and dirty solution to built in t-shirt pockets. I like to move the pockets towards the front of my body for easier access to my cell phone, but that’s simply more comfortable for me. I also will sometimes secure the t-shirt using a binder clip, that I’ll use to clip my t-shirt to my bra.

My Cat Is Not Zero Waste

September 21, 2016August 14, 2018 / Yen-Van Tran / Leave a comment

09.21.2016

0800

Trying to create zero trash for my cat is almost impossible. I’ve tried, but due to some medical conditions, it’s virtually impossible. I have a male cat and he was neutered when he was younger. Unfortunately, male cats who are neutered, are more prone to urinary tract infections and therefore, require special diet food that has a low sodium content. Also, in order for him to not develop another urinary tract infection, he needed fresh water constantly. We bought him a small drinking fountain which he helped himself to. These two requirements produced empty tin cans of cat UTI management food as well as charcoal filters.

As he aged, he developed Diabetes and requires insulin shots twice a day. This required insulin medication as well as insulin needles. He’s a large cat, but he’s always been a large cat so weight gain was his genetic default. Lucky for us, he’s always been an indoor and outdoor cat, so he always used the backyard as his giant toilet. But with him being an indoor and outdoor cat, he required flea medication. I’ve been asked “Why don’t you just make him an indoor cat? It would cut back on the flea medication trash that you produce.” But forcing an animal to stay inside when we clearly have outdoor roaming space for him seemed unnatural to me. I wanted him to roam free and go play outside when we weren’t home. So the diabetes and flea medication produced tin cans of glucose management food, insulin needles, insulin medication and the flea applicators.

Over the years, he also got into a few fights with other cats or raccoons that roamed the neighborhood. For those special occasions, he required medication and sometimes even surgery which produced trash as well. I usually return the pill bottles and jars to the veterinarian so they can dispose of it. I’m lucky that I live in an area that allows free medical waste dumping, and even if I didn’t, I know my veterinarian will collect the medical waste from his patients for a small fee.

As for toys, he never loved to play with a lot of toys. In fact, he really only likes his catnip pillow, shoelaces and metal chain necklaces . I had a catnip plant that I grew for him awhile back and once in awhile, I would dry the catnip leaves and compost the old catnip. I would then refill his pillow with new dry catnip. Unfortunately he liked it so much that he would lay on it and eventually crushed the life out of it. That too went into the compost bin. I’m lucky that he’s easily entertained. He also never wanted his own bed, he always just adopted any place in the house to sleep.

Facts:

Urinary Tract Infection Medical History = Prescription Diet c/d canned food & Filtered water with charcoal filters
Diabetes II Medical History= Glucose Management m/d canned food, insulin needles, insulin medication
Indoor & Outdoor cat = Advantage Flea Medication BUT no litter box
Entertainment = Catnip pillow, but I refill the catnip pillow with fresh catnip. He just likes to play with shoelaces and metal chain necklaces.

So the recyclable items that I do produce are the tin cans of UTI food and diabetic food. His insulin medication, insulin needles and other medications are also recycleable, but considered medical waste recycling. The charcoal filters and advantage flea medication are the items that do end up in the landfill. I actually have a separate jar of trash that comes from owning a cat. He also no longer uses the water fountain that used the charcoal filters, he requests fresh water from the faucet when he’s thirsty with a drawn out meow.

Trying to own a pet and not produce trash from them is quite difficult. I know this much, to take on a pet is a great amount of responsibility and it is not a simple responsibility to ignore. I am not a veterinarian and I do not know what nutrients he needs and the sufficient amount of each nutrient and vitamin, therefore I do not attempt to make cat food on my own. He has very few toys, only wants his catnip pillow, which I will stuff with fresh catnip and compost the old catnip.

I started this journey almost five years ago, so I’ve compiled a nice amount of Advantage Flea Medication applicators for cats as well as charcoal filters. He stopped using the water fountain about three years ago, so he hasn’t produced anymore trash from that. He probably won’t last through the end of this year, but it’s amazing to see how much owning a pet can add to your trash collection. Once you lay it all out and calculate the amount of trash that’s produced, it’s an eye opening realization of what you’re contributing to the landfill.

Work Desk Essentials

May 2, 2016August 12, 2018 / Yen-Van Tran / 1 Comment

05.02.2016

0830

I keep a small desk essentials kit at my work desk so that I don’t have to carry items back and forth from home constantly. I keep some loose leaf green tea along with a tea infuser, and some dry snacks. At my job there is a kitchen with a microwave, an electric kettle ready for employees, so I base my small kit on the available resources. In my bag which I do carry back and forth from home, I keep a stainless steel travel mug, and a set of utensils along with a fabric napkin. The reason why I keep my utensils and coffee in my bag is due to the fact that I like to be ready to go out to eat when the opportunity arises. I also will use my coffee mug for coffee, teas and water as well.

The variable items that I tend to carry is my stainless steel water bottle, whatever lunch I’ve packed for the day, and my “to go” breakfast which is usually oatmeal in a small mason jar. Depending on the days schedule or how much time I have before I step out of the front door I may or may not carry along the variable items.

Less Is More

January 21, 2016August 15, 2018 / Yen-Van Tran / 2 Comments

01.21.2016

0700

I bought this shirt in 2000. The shirt is from Consolidated Skateboards, a great company. I bought it because the quote sparked my interest and I’ve never been able to let it go. It’s a simple red long sleeved shirt, with only the front print that you see, and nothing on the back. I never knew how much of an impact those words would be.

When people say that I’m simplifying my life, I jokingly call my system “Being Strategically Lazy”.

When I decided to start living a zero waste life and because I was eliminating so much from my life, I was also eliminating the amount of storage area I actually needed. So here are a few things I decided to get rid of:

Dresser: I use one shelf now and I hang up the rest of the items
End Tables: I use two ottomans that have lids which I can flip over and use as mini portable coffee tables
TV stand: My TV currently sits on a book shelf. I’m planning to use a projector that will be mounted to my wall to watch movies/TV (but that’s for the future)
Filing cabinet: I digitized all of my documents and keep a small folder of the legal documents.
Nightstand: I use my drafting table stool as my stand and I made a shelf to sit at the bottom of it, so I could at least place items down. I also created a pocket so that I could have a location to place my phone when it was attached to the charger as well.
Bookshelf: I donated of one of my two bookshelves because I had digitized almost all of my books so I didn’t need the piece of furniture anymore.
Futon: I donated my futon and replaced it with a couch 🙂 So it’s technically a replacement piece

I have:

1 four level bookshelf
1 couch with two ottomans
1 bed
1 drafting table, which I use as my desk
1 hope chest, which I use as my seat at my desk
1 “nightstand” (I use the chair from my drafting table set as my nightstand)
1 dining table with 6 wood fold up chairs
1 IKEA Poang Chair

I think getting rid of the dresser made the biggest impact because it wasn’t just the frame of the dresser or the drawers themselves, but it was also the amount of the contents stored within each drawer. There’s another article I read which might be of interest for those who want to read more about this: 15 Pieces of Furniture You May Not Really Need

It certainly helped me look at the use of furniture differently. Here’s my little nightstand contraption. I made the pocket from an old pair of jeans and I used pink shoelaces as ties for hanging the pocket. I used an old picture frame as a flat surface on this nightstand and attached it with some sticky velcro dots that were left over from another furniture set. I found a bag of pink shoelaces at my aunt’s house, she was going to throw it out, so I took it home. I keep all of my velcro straps because velcro is amazingly versatile and I keep extra metal rings and shoelaces for projects like these.