Upcycling Milk Crates to a Shoe Rack

02.06.2018

0600

Materials:

  • 2 Milk crates (about 12″ cubes)
  • Twelve 2″ Multi-Purpose Construction Screws
  • (Optional) Three 1″ wood screws – (for creating the holes)
  • 2 Wood boards (12″ x 11-1/4″ x 1/2″)
  • 16 small screws for holding seats in place
  • Pencil

Tools:

  • Power Screwdriver
  • Table saw / Mitre Saw (or saw it by hand with a rip hand saw)

So I needed a small bench shoe rack piece of furniture. All of the designs and products I flipped through on the internet weren’t quite what I had in mind. I needed a fairly short lengthed bench that didn’t need to store a lot of shoes. I also wanted a compact design. I only own six pairs of shoes and I don’t wear them all in the same season so the rest of the room would be for my family.

I knew I had a few milk crates, which I saw the potential use for this project. It was simple idea and I knew what I wanted the final product to look like.

The interior space within each milk crate was 12″ wide, 12″ high and 10-1/4″ deep. The height of the crate was enough room for two levels for shoe storage.

DSC_8825 - Copy

Since I was going to use two milk crates, I went ahead and found two random wood boards about 1/2″ thick. The boards I found were slightly wider than the depth of the crates, but I left the extra inch for larger shoes.

So using a miter saw, I cut each piece of wood board down to 12″ x 11-1/4″.

DSC_8834 - Copy

Next I divided the interior height in half and created a guideline down the middle. Since the crate is plastic, I used an exacto blade to lightly score the midline.

DSC_8837

Using the wood screws and my power screwdriver, I pinpointed the locations of where I wanted my 2″ screws to be located. I like using the wood screws when locating holes in plastic because I can hold the shank of the screw and still guide the power screwdriver to create the straight hole.

wood screw Diagram

DSC_8838

After the holes are created, I took the 2″ Multi-Purpose Construction Screws and screwed them into the premade holes.

DSC_8841DSC_8843

For the four screws that were located further towards the back of the box, I screwed the 2″ Multi-Purpose Construction Screws inwards. And for the two screws located towards the opening of the box, I screwed them outwards.

I wanted the back of the box to be supported more since it was further back. Also, I didn’t want anything sharp located towards the front opening.

DSC_8842 - Copy (2)

I simply install each box with a board, placing the boards on top of the screws. The boards fit well and were snug enough where they didn’t move either.

Most shoes are longer than 10-1/4″, so leaving the extra 1″ helps with different sized shoes. If you need to store boots or shoes that wouldn’t fit the original designed space, you can simply remove one of the boards and the two screws closest to the opening. (I left the two screws here to show the original design)

So there you have it, you can create a simple seat and shoe storage very quickly and with simple materials. You can install a wood board on top to create a bench or stack these crates on top of a 2″ x 4″ frame to have one more level. There’s a variety of designs this can break out into. I might just do that when the spring season rolls around.

Hope this post jogged up ideas!

DSC_8858 - Copy

DSC_8853 - Copy

Update:

I wanted to secure a seat on top of the crates so I took another extra piece of wood board and lined it next to the piece I usually keep on top of the creates.

DSC_9711

I took my pencil and traced the crate pattern on the underside of each board and then used small screws to outline at least two crate holes using the small screws. In order to know where I had to place my screws, I flipped my screws over so that they would be standing on their heads and then gauged where the sharp end of the screw would land. The head of the screws had to hug the insides of the traced corner, so I knew where to place it. Wherever the screw could touch both edges of the location, was where I knew I had to place the screw.

I measured the location for the screws in this manner because I wanted the screw to fit right inside of the hole I traced. The head of the screw as well as the thread of the screws had to fit comfortably into the existing holes, once it was flipped over.

DSC_9708

I didn’t screw the screws in the entire length of the thread, so be very aware of the depth of the wood piece you pick out and the screw length that you choose as well. The idea here was to still have the screws sticking out of the board so it would fit nicely into the holes that were traced.

DSC_9708DSC_9705

Once I placed the boards back onto the crates, the top was created into a quick seat to use while putting on shoes (or taking them off).

 

DSC_9721

So there you have it! I like this much more now with the seat on top, and secured into place.

 

Advertisements

Upcycling Denim Jeans

01.30.2018

0600

Materials:

  • One pair of denim jeans

Tools:

  • Sewing machine
  • Sewing Kit

So recently I started going auditing my traveling items such as my bath bag, travel accessories as well as my sport bags. I wanted to find 3 pieces of clothing to donate, but I also noticed that my bath bag wasn’t containing my bath items comfortably.

So I had the choice to go buy/find a new bath bag or find another solution. Out of the items I decided to donate, I found a tank top, sweater and a pair of jeans. Denim is one of my favorite materials to work with. I love upcycling denim into new items. The idea of donating the pair of jeans wasn’t exactly what I thought I would do, so I decided to make a stand up bath bag for myself, or at least a few stand up bags.

I’ve owned bath bags before, but the material was with a polyester or nylon blend. Over time, my bath bags would have soap or toothpaste residue stains. I figured that with a denim bath bag, I could simply throw it into the washing machine and it would clean easily.

DSC_8685

I divided each leg in half by folding it in half. I then cut the legs off from the pair of jeans and then divided each piece in half.

DSC_8695

I turned each of them inside out and designated the wider end of the pieces as the bottom of the bag and the smaller ends as the top of the bag.  I folded the top of the bags down to create the drawstring tube. This is where I wanted to install the drawstring later.

DSC_8697 - Copy

I hemmed the bottoms of the bags by simply sewing a sew line across the bottom. I then sewed the drawstring tube. I measured 2″x2″ squares on the corners on bottom.

I marked these white dots on BOTH SIDES OF THE BAG, near the bottom section of the bag. These white dots will be used as guides of where you will sew in the next step.

DSC_8699 - Copy

I then flipped the bag upside down, and so that the right side seam was facing up. I then folded the bottom of the bag to create a diamond shape. You should be able to locate all four dots that were created in the last step, when molding the diamond shape.

DSC_8704 - Copy

The dots are guides to sew where you will sew horizontally across the diamond. After sewing the two lines, the diamond should look like this.

DSC_8712DSC_8718

Since I was initially thinking of making a new bath bag, I wanted to sew a small pocket inside of that bag. I had this extra pocket left over from my Handmade Handkerchiefs project, so I added it on the inside. To find the opposing edges of the box, you can locate it by finding the perpendicular lines of the top and bottom hemmed lines.

DSC_8715 - Copy

If you want to make a small pocket inside, you can sew a piece of material to the inside of the bag, as long as you leave to top of the material open.

In this case, because the pocket was more than half of the height of the bag, I placed the pocket towards the bottom of the bag. I also knew that I would be folding the bag down when in use, so placing it towards the bottom gave me room for the top to be folded down.

DSC_8719

Once I pulled the drawstrings through the bags, this is what they looked like. They stand up pretty well, and I can fold them down to create a top frame for the boxes.

DSC_8721

This is what my bath bag looks like now.

DSC_8795

I like the fact that I can simply fold my bag down and be able to access everything I need inside. I also have the habit of attaching a ring to the interior of any bag. So I attached a metal ring to the inside seam of the bag, because I wanted to hang small bath items for easy access.

So there you have it. This was my solution to my travel bath bag issue. I genuinely love denim and to make these stand up drawstring bags with this material is one of my favorite kinds of sewing projects that I like to get involved in.

I used my other bags for some camera gear and for another bag I use for traveling. The denim creates a nice thickness for the bottom of these bags, which is why I like to use them for electronics.

DSC_8794

As a bonus…

I made a bag out of the top part of my denim jeans. I simply flipped the top inside out and hemmed the pant leg openings.  Due to the nature of how the jeans were cut and sewed, I folded the outer edges of the jeans inward when I hemmed them.

DSC_9368DSC_9369

I then sewed a zipper to the top opening of the jeans using sewing pins to hold the zipper in place and then sewing it to my pants. I used the same sewing steps to attach the zipper as to when I  Created Slim Hanging Organizers.

DSC_9371

Since my zipper wasn’t quite long enough for the length of the jeans, I closed off the jeans by sewing the top together.

DSC_9372

DSC_9373

I used an extra tie to create the handles of this bag. This was a simple choice but some people may prefer to use a belt or something more to their taste. I chose the tie because I wanted to be able to throw everything into the washing machine.

DSC_9375DSC_9381

And as always, I attached a metal ring to my zipper for a slightly easier access.

I use this bag to hold some smaller items that need a bit of cushion like camera gear or smaller electronics.

DSC_9383

 

 

 

Creating Fabric Boxes

01.16.2018

0600

Materials:

  • Hanging Fabric Shelf Organizer
  • Quilt Batting (optional)

Tools:

  • Sewing Machine or thread and needle
  • Sewing Kit
  • Ruler
  • Pencil
  • Iron and Ironing Mat

Hanging Fabric Shelf Organizer

So I had a hanging fabric shelf organizer which I had replaced by sewing slim hanging organizers from pillow cases. You can find that blog post at Created Slim Hanging Organizers. But once I replaced the canvas hanging organizer, I didn’t know what to do with it. So I decided to create small fabric boxes with the leftover material. I first took it apart, literally took it apart piece by piece. I recycled the cardboard and I was left with rectangular pieces of canvas.

This project works best if you have perfect square material, but I didn’t want to waste any material so my pieces were left as rectangular pieces. Rectangular canvas pieces yield rectangular shaped boxes. Square fabric pieces will result in perfect square boxes.

DSC_7915 - Copy

So I first worked on the larger fabric piece. I first sewed the edges of the fabric so it wouldn’t com apart. I wanted these boxes to have a rougher look to them so I didn’t hem the edges. You can insert a fitted quilt batting piece in between your fabric pieces if you are using a softer fabric and if you want your box sides to be a stiff frame. I didn’t use batting because my material is canvas in this project.

I folded it in half (doesn’t matter which direction), and then I marked off a 3 inch by 3 inch triangle on each corner of the folded side. These triangle marks are the red lines in the photo. The larger the triangle, the higher the height of the fabric box will stand.

 

DSC_7921-2

I opened it up and I folded the fabric piece in the perpendicular direction, with the first set of triangle marks still facing upwards.

DSC_7925

I then proceeded to fold the fabric and mark off the second set of 3 inch by 3 inch triangle on each corner of the folded side. These are located with the blue lines in the photo.

DSC_7929

From there, I sewed over the lines of where I had marked each set of triangles. I sewed the blue lines first. I then opened up the fabric piece, lined up the other corners in order to sew over the red lines.

DSC_7937DSC_7944

Once you sew all of the four corners, when you open the fabric, it should look something like this. However, now you have to flip the box inside-out. Once you do that, the rectangular tabs you created should be on the inside.

DSC_7945DSC_7948

With the four triangle flaps sticking straight up, fold them down to create a straight edge of the box. You can pin it down with sewing pins to watch the shape take form. Once you fold down all of the standing flaps, you should have a similar box like the photo below.

DSC_7952

Now you just need to sew the standing flaps down to create sharper straight edges of the box and then sew the flaps on the inside of the box to keep them flat against the sides.

DSC_7957

I’ve used the large fabric boxes to organize items in my linen closet as well as my camera gear items. Although these aren’t perfect squares, I like the idea that these fabric boxes are easily modified to most objects.

DSC_7960

For the smaller piece of fabric, I hemmed the edges to keep the fabric together and then I measured a 2 inch margin all around the edges. Here, you can insert a piece of fitted quilt batting before sewing the edges together, to give your fabric box a more framed look.

DSC_7962

I folded each edge over and ironed the lines to define the bottom of the box.

DSC_7963

Using sewing pins, I folded in each corner and held them there. These smaller triangles will help define the corners of the box.

DSC_7971

For each triangle corner, I found the center of the triangle and folded it in half. Once the triangle folded in half, the edges of the box came together naturally. I hand sewed these edges together by using a running stitch pattern. I sewed the running stitch in one direction, then simple went back the opposite direction to fill in the gaps in the pattern.

DSC_7975DSC_7978DSC_7980DSC_7982

Once I sewed all four corners, I proceeded to sew the triangle flaps on the inside of the box to the walls.

DSC_7987DSC_7988

I’ve used the smaller fabric boxes to keep smaller items organized that sit on shelves and table tops. So there you have it, these were very simple boxes made from the canvas material I had left over from the hanging fabric shelf organizer. You can use pretty much any fabric you want, but you may need to use quilt batting to strengthen the sides of the boxes.

DSC_7997

Upcycled Coat Rack From Spoons

01.09.2018

0600

Materials:

  • Wood board (18 inches long x 5 inches wide 1-1/2 inches deep)
  • Four 3 inch wood screws
  • Ten 1-1/2 inch wood screws
  • 5 Spoons

Tools:

  • Power Drill
  • Power Screwdriver
  • Needle Nose Pliers
  • Slip Joint Pliers
  • Safety glasses
  • Gloves

DSC_8162DSC_8164

So I wanted to make a coat hanger but I didn’t want to buy one. Apparently I had materials at home to make one of my own. This project is a fairly easy DIY for any of you who are curious.

My board was 18 inches wide and I wanted a minimum of 1 inch on each side, for margins. This left me with 16″ to work with. So initially I wanted to use 7 spoons for the hangers, but after I measured the distance, I decided to only use 5 spoons.

DSC_8171-2

I divided the board up into three sections. The height of my board was 5-1/2″, but if you don’t want to use numbers, simply take a piece of paper and fold it into thirds. Then with a pencil, mark the first line and then the second. I wanted to offset my rows of spoons so the red line is for the top row of spoons and the green line is for the center of the bottom row of spoons.

Where the red line and margins intersect is where I drilled my top mounting holes. My bottom mounting holes is where the green line and the margins intersect. These holes are marked by the yellow circles in the image.

DSC_8179-2

For the spoons, I wanted to drill 2 holes to mount each spoon and I knew I had to create hooks by manipulating the spoons. I picked out a drill bit that was a similar size diameter of my screws I was going to use on the spoons. Usually I choose a drill bit smaller than my screw, but that working with wood only. When working with metal, you want a drill bit that the same size as the screw since metal won’t give. Also, if you don’t choose a drill bit smaller than your screw, there’s a good chance you’ll strip the screw’s threads as you drill.

The green line marks the point of where I wanted my spoons to bend upwards, so they could be used as hooks.

DSC_8173-2

When I drilled the holes, I wore gloves and my safety glasses because the metal slivers would fly off of the power drill. I applied slow but steady pressure while holding the spoon still and then I dumped the metal shavings into one side of my purple container. I did this to contain the shavings but also because it would be easier to discard them after I finished.

DSC_8184

I first started bending the spoons by using the edge of my step ladder, then I used my Slip Joint Pliers to hold the spoon while using the Needle Nose Pliers to bend the spoons into hooks.

DSC_8169

Once all of the spoons had holes drilled into them, I spaced the spons apart from each other in three inch increments. I proceed to attach the spoons to the board. For the wall mount attachment holes, I sunk the holes into the wood so that there was a slight design detail. I initial had made 2 drill holes so that I could mount it to the stud in the wall (those are the extra holes you see floating on the left half of  the board), but I changed my mind and decided to directly attach it to the drywall instead. Because I was planning to use three inch screws, I knew that mounting it to the drywall wouldn’t be a problem.

But because I changed my mind on which drill holes I wanted to use to mount the coat rack, I now had two random holes that looked out of place. To fix this, I mirrored the holes to the other side of the board and then filled in the extra holes will extra wood filler we had left over.

DSC_8185

I centered my coat rack and attached it to my wall. As you can see, the mistake holes look like design elements with the wood filler.

DSC_8198DSC_8200

So there it is, my coat rack made from spoons. These spoons are a few extra spare spoons from my mother’s kitchen and I really like that I was able to upcycle these extra spoons, knowing that a part of her kitchen was now used in an item I really needed. It’s a nice homage to my mom in a subtle way.

Our homes and possessions hold a great deal of different types of materials in which we can reuse and upcycle into new items.   Once you breakdown how different types of materials are used, the possibilities are endless. Scan your home and surroundings, I’m sure you’ll find a lot of resources.