Sofa Armrest Organizer

October 14, 2019October 14, 2019 / Yen-Van Tran / Leave a comment

10.14.19

0600

Materials:

Two Curtains at 5′-10″ in length

Tools:

Sewing Machine
Sewing Kit

I have an extra set of curtains, which I didn’t want to use anymore. I decided to create a sofa armrest organizer with both curtain pieces. Both curtain pieces were 5 foot 10 in length, and 27 inches wide.

I wanted my sofa armrest organizer to sit at a certain height off the ground, but I also wanted the top half to also tuck underneath the couch cushion. I first measured how high off the ground I wanted my couch armrest organizer. Since I needed to hang it over the sofa armrest and then wrap back over the arm to tuck underneath the cushion, that left about 47 inches to tuck underneath the cushion.

I wanted to store books in the first organizer, which would be fairly heavy, so I needed a lot of the material to tuck under the seat cushion to hold it in place. I actually wanted the top part of the organizer to tuck underneath an entire sofa cushion width, due to the weight that would be applied.

FIRST SOFA ARMREST ORGANIZER:

When I measured out my first design, I wanted the pockets for my books to be 14 inches in height. I first hemmed all of the edges and then I folded one edge to create the 14″ tall pockets. I sewed around the edge of the folded piece (yellow arrows) and then divided the pocket in half, and sewed a dividing line down the center to create two tall pockets (red arrow). These pockets will be able to hold my books and paperwork that I’m currently working on. I wanted my pockets to be a bit taller than the standard paper size (8.5″ x 11″), due to the fact that I knew the width of the pocket might eat up some of the height. I also wanted to be able to hide my books and paperwork, so my pockets wouldn’t look like they were overflowing with paper.

To attach the sofa armrest organizer, I removed the couch cushion on the side of the couch, located how high I wanted to hang the organizer, and then replaced the couch cushion. Since the top half of the fabric organizer is tucked under the couch cushion, it stayed in place.

SECOND SOFA ARMREST ORGANIZER:

I also wanted to create a second design, which would have smaller pockets for smaller items. My second design would have 10 inches in height for the books, and 6 inches for smaller objects.

Using the same sewing method as the first design, I hemmed all of the edges of the fabric material, and then measured 16″ of material at one end. I folded up the 16″ material, sewed along the outside edges of the tall pocket (yellow arrows), which created a giant 16″ tall pocket.

I then took the bottom 6″ of the pocket and folded it up, to create a shorter 6″ pocket at the bottom. This 6″ tall pocket also helped create the 10″ pocket behind the smaller pockets. I then sewed on both of the side edges of the fabric piece (red arrows) and then sewed a dividing line (blue arrow) to create a total of four pockets for this design. I sewed the edges of this design, all the way to the top of the pocket to reinforce the side edges.

Using the same method as the first sofa armrest organizer, I located where I wanted the organizer to hang on my armrest and I tucked the top half of it under the couch cushion on the end.

Since these sofa armchair organizers are made of fabric material, I can toss them into the washing machine and wash them easily. I can also fold them up and put them away if I don’t need to use them. Fabric is my favorite material to work with since it can be taken apart and reused multiple times. I love that it is a very flexible medium and I was able to put my old curtains to good use.

Mending Items Versus Buying Items

July 29, 2019August 5, 2019 / Yen-Van Tran / Leave a comment

07.29.2019

0600

If you read about my Fast Fashion post, it relates to this one. If not, please go check it out. Even though I do by thrift store items, I will still mend an item to save it from a donation. Sometimes I will mend my items and then I donate the item. For instance, I found an old shirt at my aunts house. It had a few holes in it but overall, I liked the color and I didn’t mind the cut of the shirt. The color went perfectly with my color palette for my capsule wardrobe, so I really wanted to save it from being donated. I just needed to mend the shirt, so it would be decent to wear.

Now I have an almost new shirt.

Whenever I upcycle clothing, I always keep scraps of the leftover clothing item. In my Reusing Fabric and Thread blog post, I wrote about keeping my fabric scraps in a small bag. I literally have a bag of scraps. I love fabric, and the use of fabric in different products, (depending on the thread count, material, and the way fabric is sewn together,) can be a very durable material.

Some shirts have higher thread counts, which lends them to become excellent candidates to upcycle into grocery bags, or other heavy duty bags. The smaller scraps that I keep, I always try to find a use for them. Whether it’s going to be upcycled into a small project or large project, the one thing I can count on is that I can throw it in the washing machine to clean it.

If I had a choice to make, with picking and choosing reusable products, I prefer to choose items that I can wash easily. I don’t like to buy items which require a special cleaning method or liquid to clean. I like to sew and mend items, because the product that I’m usually mending, only needs to be washed with soap and water.

If you reflect on the products that you use daily, the majority of them are probably sewn together: your clothes, handbags, wallets, car seats, bedding, upholstery, etc. Knowing how to sew and understanding how to repair fabric products has been a life saver for me. I actually learned how to sew by hand, and didn’t learn how to use a machine until years later.

Learning how to mend items can save you money, time and stress. Even the simple act of sewing on a button is helpful. You can save a simple dress shirt, like I did, from sending it to a donation station.

Upcycling A Shoe Organizer

October 2, 2018October 2, 2018 / Yen-Van Tran / Leave a comment

10.02.2018

0600

Materials:

One over the door shoe organizer
X-acto blade
Cutting mat (or cardboard, plywood, some type of surface you’re willing to cut into and can damage just a little bit)
4 Safety Pins

Tools:

Sewing machine
Sewing Kit

So I’ve owned an over the door shoe organizer for awhile. I didn’t use it a lot because I didn’t have many pairs of shoes. When I started to declutter my life and minimize my possessions, I kept it because I still liked the design and I knew I could use the material to create something else.

Because I’m not a fan of keeping items out in the open, much less hanging them out in the open, I knew I wanted to upcycle this shoe organizer into smaller organizers. I personally like things to be put away. My minimalist, zero waste lifestyle lends my living space towards clean surfaces and minimal decor. So I wanted to create two smaller organizers which could be hung up in the closets.

The goal was to create two separate organizers that were each 2 pockets across by 3 pockets vertically on each side of the smaller organizer. So each side of the hanger would hold a grid of pockets that was 2 pockets across by 3 pockets vertical.

First I cut the shoe organizer in half.

I then folded each organizer in half (vertically) to find out where I wanted to locate the hangers.

I then placed each hanger on each organizer, as I wanted them to sit. I wanted to place each hanger so that the top bars of the hangers would still be protected by the fabric. I only wanted the neck of the hanger to stick up and out of the fabric so the fabric organizer would sit higher on the hanger. The hanger would have more control of the overall weight of the items inside each pocket when it was hung up.

I placed the hangers where I wanted each hanger to be located on each organizer and then marked the location of the bottom bar. I needed to make a mark at those locations, because that’s where the bottom of the openings for the hangers would pass through.

Using the X-acto blade, on the folded edge, I carefully cut a straight line of where the hanger would stick out. I cut along the mid line of the fabric grid pattern and only cut enough for the hanger to fit. You can sew the edges of these openings if you want a clean and sturdy structure around the edge of the opening. I suggest using a running stitch to do that, if you choose to.

Using the bottom of opening as a location marker, I sewed both sides of each organizer together. I wanted the backs folded and sewed to one another to create a more sturdy central structure. I sewed from the bottom of each opening, around and up to the other side, making sure I stopped at the other marker.

The idea was that I wanted to seal the two flaps of pockets to each other, but leave enough room for the hanger to slide in and out of the design.

Once the hanger is slid into place, the flap should allow the user to remove the hanger if necessary. I used a hem stitch to secure the top of the opening on the folded edge (see below). I did this because I know that the weight of the the organizer will tear the opening over time. I wanted to secure the top of the opening and reinforce the structure.

I stitched an extra line above the hanger (towards the folded side of each hanger), but underneath the pocket flaps, to reinforce extra support for the organizer.

Using a safety pin, I pinned the opened edge approximately where the top of the hanger was located on the opposite side. This way, the hanger can be removed easily when it comes time to wash it or put it away. The safety pin will act as a closing mechanism to hold the hanger in place.

So there you have it, this is how I upcycled my over the door shoe organizer. Although, I technically only created smaller shoe organizers, I had the idea that I could use these smaller organizer to store smaller items such as jewelry, scarfs, socks, etc., that can get lost in a closet. Basically, anything you might store in the top drawer of your dresser, you might use this for. I don’t use a dresser, so this product can be useful for me. Right now I actually use a few of the pockets to keep some running and workout items organized. I like this design for the fact that it’s double sided and it can be folded up and put away if it’s not being used. Hopefully this post might spark some organizational ideas for your life.

Until next time!

Creating A Locking Mechanism For My Carabiners

May 16, 2017August 12, 2018 / Yen-Van Tran / 1 Comment

05.16.2017

0700

I’m a big fan of carabiners. I have all different types and designs, however, I tend to favor the Asymmetrical D-Shape. On a whim a few years back, I bought two S-Binder carabiners. I really liked this design because the items I would place on the bottom half of the carabiner were separated from the top half. The top lever was the lever that I would use to hook and unhook the carabiner to other objects.

This also lead to an issue with the way in which I used it. Each time I would wrap my hands around the carabiner to press open the top lever, I would inadvertently press my palm against the bottom lever and the objects had a very good chance to slide out. This involuntary action happened a few times and I had to come up with a quick solution.

First, I wrapped a small piece of Velcro around the bottom lever, but over time, the Velcro started to become weaker and would become unattached, which left the end flap of the Velcro unattached. I knew I had to come up with a more permanent solution. I knew other carabiner brands sold their Asymmetrical D-Shape carabiners with locking mechanisms or had an external accessory that helped lock their levers in place. I had to make my own locking mechanism in order for me to not drop my keys all over the place.

I took a old piece of an iron on elbow patch (I had bought a set years ago and never used them all up), and I cut the length to the distance that it would take to cover the lever and half of the basket of the carabiner. (If you don’t know where the ‘basket’ is, I labeled all of the parts of a carabiner in the first image).

With a few sewing needles, I marked the locations of the fabric of which I would have to sew the fabric together. I removed the fabric from the carabiner and sewed it up. I needed to create a snug fit for the locking mechanism so that the fabric didn’t move easily when in use. When I sewed my second locking mechanism, I sewed it a little too snug, but with fabric, you have a slight chance to stretch the length and width of any product due to the material. This was material for iron-on elbow patches, so it was a very, very slight stretch .

Once I was finished sewing both the locking mechanisms, I slid the pieces on, moved my key rings over them and then slid it back over the levers. It’s a simple solution to a very basic tool I use everyday.

If you use any other kind of fabric, perhaps 100% cotton, you may have to sew it a little tighter because cotton tends to stretch more. And, you may want to extend the length of the locking mechanism so that it can’t slide back and forth on the basket as easily. The idea is to make the fabric slight “stuck” on the spine of your carabiner. If it has a hard time sliding around the basket, then it most likely won’t slide around when in use.

I hope this might give any of you some ideas as to how to approach design problems such as this one. Happy sewing and don’t loose those keys!