upcycling

Sofa Armrest Organizer

/ Yen-Van Tran / Leave a comment

10.14.19

0600

Materials:

  • Two Curtains at 5′-10″ in length

Tools:

  • Sewing Machine
  • Sewing Kit

I have an extra set of curtains, which I didn’t want to use anymore. I decided to create a sofa armrest organizer with both curtain pieces. Both curtain pieces were 5 foot 10 in length, and 27 inches wide.

I wanted my sofa armrest organizer to sit at a certain height off the ground, but I also wanted the top half to also tuck underneath the couch cushion. I first measured how high off the ground I wanted my couch armrest organizer. Since I needed to hang it over the sofa armrest and then wrap back over the arm to tuck underneath the cushion, that left about 47 inches to tuck underneath the cushion.

I wanted to store books in the first organizer, which would be fairly heavy, so I needed a lot of the material to tuck under the seat cushion to hold it in place. I actually wanted the top part of the organizer to tuck underneath an entire sofa cushion width, due to the weight that would be applied.

FIRST SOFA ARMREST ORGANIZER:

When I measured out my first design, I wanted the pockets for my books to be 14 inches in height. I first hemmed all of the edges and then I folded one edge to create the 14″ tall pockets. I sewed around the edge of the folded piece (yellow arrows) and then divided the pocket in half, and sewed a dividing line down the center to create two tall pockets (red arrow). These pockets will be able to hold my books and paperwork that I’m currently working on. I wanted my pockets to be a bit taller than the standard paper size (8.5″ x 11″), due to the fact that I knew the width of the pocket might eat up some of the height. I also wanted to be able to hide my books and paperwork, so my pockets wouldn’t look like they were overflowing with paper.

To attach the sofa armrest organizer, I removed the couch cushion on the side of the couch, located how high I wanted to hang the organizer, and then replaced the couch cushion. Since the top half of the fabric organizer is tucked under the couch cushion, it stayed in place.

SECOND SOFA ARMREST ORGANIZER:

I also wanted to create a second design, which would have smaller pockets for smaller items. My second design would have 10 inches in height for the books, and 6 inches for smaller objects.

Using the same sewing method as the first design, I hemmed all of the edges of the fabric material, and then measured 16″ of material at one end. I folded up the 16″ material, sewed along the outside edges of the tall pocket (yellow arrows), which created a giant 16″ tall pocket.

I then took the bottom 6″ of the pocket and folded it up, to create a shorter 6″ pocket at the bottom. This 6″ tall pocket also helped create the 10″ pocket behind the smaller pockets. I then sewed on both of the side edges of the fabric piece (red arrows) and then sewed a dividing line (blue arrow) to create a total of four pockets for this design. I sewed the edges of this design, all the way to the top of the pocket to reinforce the side edges.

Using the same method as the first sofa armrest organizer, I located where I wanted the organizer to hang on my armrest and I tucked the top half of it under the couch cushion on the end.

Since these sofa armchair organizers are made of fabric material, I can toss them into the washing machine and wash them easily. I can also fold them up and put them away if I don’t need to use them. Fabric is my favorite material to work with since it can be taken apart and reused multiple times. I love that it is a very flexible medium and I was able to put my old curtains to good use.

TerraCycle Programs

/ Yen-Van Tran / Leave a comment

09.16.2019

0600

TerraCycle offers a range of free programs that are funded by conscientious companies, as well as recycling solutions available for purchase for almost every form of waste.

TerraCycle offers free recycling programs funded by brands, manufacturers, and retailers around the world to help you collect and recycle your hard-to-recycle waste. Simply choose the programs you’d like to join; start collecting in your home, school, or office; download free shipping labels; and send us your waste to be recycled. You can even earn rewards for your school or favorite non-profit!

TerraCycle reuses, upcycles, and recycles waste instead of incinerating or land filling it. This moves waste from a linear system to a circular one, allowing it to keep cycling in our economy. 

You can collect points, by collecting trash for your specific program and then redeeming your points. You can redeem your points by either receiving a cash value, or you can donate the points to charity. There’s a list of charities that team up with TerraCycle, in which you can choose to donate your points to.

I always donate my points, since I think this program is a great way for charities and companies to get involved with creating less waste, and I really don’t value the cash redemption as much.

Some of the charity organizations I was looking at to donate my points were:

  • 100 points = Help safeguard 1 acre of rain forest for 1 year in the Northwest Gaia Amazon.
  • 1 point = Help http://www.Carbonfund.org to reduce a 2 pounds of emissions from the atmosphere.
  • 1,000 points = Help http://www.Carbonfund.org to reduce a metric tonne or 2,205 pounds of emissions from the atmosphere.
  • 300 points = Have a tree planted in an American forest through Arbor Day Foundation
  • 300 points = You can provide one year’s supply of clean drinking water to a person who otherwise would lack access to this most essential element. 
  • 625 points = You can help the D’Addario Music Foundation give one child a free music lesson.
  • 2500 points = You can help the D’addario Music Foundation provide a child with 4 music lessons for a week. Kids who study music are 5x more likely to stay in school, graduate on time and apply to college.
  • 100 points = For every 100 points, TerraCycle will send $1 to the American Red Cross to provide aid to those affected by natural disasters.

For this round, I decided to split my points between a couple of different charities. I decided to redeem my points with:

  • Providing one year’s supply of clean drinking water to a person who otherwise would lack access to this most essential element
  • Help http://www.Carbonfund.org to reduce emissions from the atmosphere

If you want to participate in the TerraCycle programs, check them out at https://www.terracycle.com/en-US/select-country to see which programs you can join. The participating companies change often, so check back with the website to see updates. There are a lot of programs to choose from and supporting the partnership between TerraCycle and the participating companies creates more awareness to how much trash we produce, and how companies take responsibility for the trash they pass onto us consumers.

Mending Items Versus Buying Items

/ Yen-Van Tran / Leave a comment

07.29.2019

0600

If you read about my Fast Fashion post, it relates to this one. If not, please go check it out. Even though I do by thrift store items, I will still mend an item to save it from a donation. Sometimes I will mend my items and then I donate the item. For instance, I found an old shirt at my aunts house. It had a few holes in it but overall, I liked the color and I didn’t mind the cut of the shirt. The color went perfectly with my color palette for my capsule wardrobe, so I really wanted to save it from being donated. I just needed to mend the shirt, so it would be decent to wear.


Now I have an almost new shirt.


Whenever I upcycle clothing, I always keep scraps of the leftover clothing item. In my Reusing Fabric and Thread blog post, I wrote about keeping my fabric scraps in a small bag. I literally have a bag of scraps. I love fabric, and the use of fabric in different products, (depending on the thread count, material, and the way fabric is sewn together,) can be a very durable material.

Some shirts have higher thread counts, which lends them to become excellent candidates to upcycle into grocery bags, or other heavy duty bags. The smaller scraps that I keep, I always try to find a use for them. Whether it’s going to be upcycled into a small project or large project, the one thing I can count on is that I can throw it in the washing machine to clean it. 

If I had a choice to make, with picking and choosing reusable products, I prefer to choose items that I can wash easily. I don’t like to buy items which require a special cleaning method or liquid to clean. I like to sew and mend items, because the product that I’m usually mending, only needs to be washed with soap and water.

If you reflect on the products that you use daily, the majority of them are probably sewn together: your clothes, handbags, wallets, car seats, bedding, upholstery, etc. Knowing how to sew and understanding how to repair fabric products has been a life saver for me. I actually learned how to sew by hand, and didn’t learn how to use a machine until years later.

Learning how to mend items can save you money, time and stress. Even the simple act of sewing on a button is helpful. You can save a simple dress shirt, like I did, from sending it to a donation station.

Reusable Facial Cotton Pads

/ Yen-Van Tran / Leave a comment

11.19.2018

0600

Materials:

  • 3-4 Cotton Handkerchiefs, pattern or color of your choice (Note: if you tend to use makeup/liquids that are oil or wax based, the substance will leave a slight film on the fabric, over time)

Tools:

  • Sewing machine
  • Sewing Kit
  • Iron
  • Ironing Mat/Board

DSC_0499When I started eliminating single use products out of my life, I really had no need to replace all of the products with reusable ones. But as we all know, life changes, and we adapt to it. Years ago, I had used single use, cotton rounds to remove makeup and nail polish. When I transitioned to a minimalist zero waste lifestyle, I eliminated nail polish from my life and only used vegan makeup. My vegan makeup removal process does not require cotton pads to remove the makeup, just soap and water.

Recently, I was gifted a facial skin care kit and I had no cotton pads to use with it. So now, in order to use the gift, I needed to prepare beforehand, and sew a pack of reusable facial cotton pads.

So for this project, I took a shortcut in which, I used a few handkerchiefs I already had. I knew I only needed rectangular cotton pads about 2″ x 1″, just wide enough to hold across my three fingers when using them.

how-to-draw-open-hand-palms-up-cartoon-easy-steps

I know that the makeup industry standard is to use “cotton rounds”, but when I broke down the division of my handkerchiefs, it was easier to make cotton ‘rectangles’ instead. I took each handkerchief and divided it in half, then divided those pieces in half, and then divided those pieces in half, until I broke down my handkerchief into small squares, about 2″x 2″. These squares will be folded in half and sewed into rectangles. This way, the cotton pads with have two fabric layers.

Technically, the final size of the cotton pads is up to you, because if you end up with a larger square, that only means you get to use a larger rectangle surface to use on a day to day basis.

So I took one of my handkerchiefs and folded it in half and cut it. I then folded the rectangles in half, which resulted in large squares. I folded the large squares in half and then folded those rectangles in half to create the small squares.

DSC_0375 - CopyDSC_0380 - Copy

Using my iron and ironing mat, I folded each small square in half, to create the crease for the cotton pads. This crease is where the rectangle shape starts to form, and to save time, I would iron the pieces four at a time. 

DSC_0389 - Copy

In order for me to iron four cotton pads at the same time, I placed four cotton rectangles in a square formation, in which the edges were placed inward and then I would iron the creases across the mat.

DSC_0467 - Copy

DSC_0411

I used my sewing machine to sew the open edges together and I chose to use the zigzag stitch and a universal needle for this project.

00- Needles-300x188

00- SEW- Straight-Stitch

The most common use of a zigzag stitch is to enclose raw edges as a seam finish. As a seam finish, one edge of the stitch is sewn off the edge of the fabric so that the threads of the fabric are enclosed within the threads of the zigzag stitch and the fabric is unable to fray because of the zigzag stitch.

Be sure to sew in from the edge slightly. Then, trim away the excess beyond the zigzag, making sure not to clip into any of the stitching. You can also use two rows of zigzag for extra “fray-stopping” power.

I started my sew line from one open end of the fabric,  and continued around the open edges. 

DSC_0472DSC_0474DSC_0480DSC_0481

I like to tie off my thread ends, but you can reverse the stitch so that it your sewing machine creates a back stitch. In other words, while you’re sewing the last leg of the fabric edge, slow down the speed of the stitch by backing off of the pedal. Slow to a speed in which you can spot each needle point going into your fabric. If you can learn to anticipate where the needle will land, then you’ll be able to get as close to the end of your sew path and create a tighter back stitch for your projects.  So, as you get closer to the end of your sew path, press the Back Stitch Lever, and hold it down, so that the direction will reverse. When you’re satisfied with the length of the back stitch, let go, and the machine should continue to push your fabric back to the original direction. (Try to get as close as possible to the end of the sew path before reversing the stitch.)

Personally, I would only reverse the direction for about half an inch. Don’t go back too far, since this is such a small piece of fabric. This back stitch will lock in your stitch. Then simply trim the thread, and you’re done.

DSC_0487DSC_0492DSC_0499

I brought home an empty coffee creamer container from work, since I liked the shape. I knew that this project was coming up, so I thought it would be a good container for my reusable facial cotton pads.   

DSC_0507

So there it is, this is how I created my reusable facial cotton pads. I hope that this post may inspire you to eliminate single use personal care accessories in your bathroom. 

Upcycling A Shoe Organizer

/ Yen-Van Tran / Leave a comment

10.02.2018

0600

Materials:

  • One over the door shoe organizer
  • X-acto blade
  • Cutting mat (or cardboard, plywood, some type of surface you’re willing to cut into and can damage just a little bit)
  • 4 Safety Pins

Tools:

  • Sewing machine
  • Sewing Kit

 

DSC_0326

So I’ve owned an over the door shoe organizer for awhile. I didn’t use it a lot because I didn’t have many pairs of shoes. When I started to declutter my life and minimize my possessions, I kept it because I still liked the design and I knew I could use the material to create something else.

Because I’m not a fan of keeping items out in the open, much less hanging them out in the open, I knew I wanted to upcycle this shoe organizer into smaller organizers. I personally like things to be put away. My minimalist, zero waste lifestyle lends my living space towards clean surfaces and minimal decor. So I wanted to create two smaller organizers which could be hung up in the closets.

The goal was to create two separate organizers that were each 2 pockets across by 3 pockets vertically on each side of the smaller organizer. So each side of the hanger would hold a grid of pockets that was 2 pockets across by 3 pockets vertical.

First I cut the shoe organizer in half.

DSC_0270-2_Shoe Organizer Diagram

 

I then folded each organizer in half (vertically) to find out where I wanted to locate the hangers.

DSC_0272-2

I then placed each hanger on each organizer, as I wanted them to sit. I wanted to place each hanger so that the top bars of the hangers would still be protected by the fabric. I only wanted the neck of the hanger to stick up and out of the fabric so the fabric organizer would sit higher on the hanger. The hanger would have more control of the overall weight of the items inside each pocket when it was hung up.

DSC_0275-2

I placed the hangers where I wanted each hanger to be located on each organizer and then marked the location of the bottom bar. I needed to make a mark at those locations, because that’s where the bottom of the openings for the hangers would pass through.

DSC_0273-2

Using the X-acto blade, on the folded edge, I carefully cut a straight line of where the hanger would stick out. I cut along the mid line of the fabric grid pattern and only cut enough for the hanger to fit. You can sew the edges of these openings if you want a clean and sturdy structure around the edge of the opening. I suggest using a running stitch to do that, if you choose to.

Types of Stiches

DSC_0279-2DSC_0277-2

Using the bottom of opening as a location marker, I sewed both sides of each organizer together. I wanted the backs folded and sewed to one another to create a more sturdy central structure. I sewed from the bottom of each opening, around and up to the other side, making sure I stopped at the other marker.

DSC_0276-2 - Copy

The idea was that I wanted to seal the two flaps of pockets to each other, but leave enough room for the hanger to slide in and out of the design.

DSC_0282

Once the hanger is slid into place, the flap should allow the user to remove the hanger if necessary. I used a hem stitch to secure the top of the opening on the folded edge (see below). I did this because I know that the weight of the the organizer will tear the opening over time. I wanted to secure the top of the opening and reinforce the structure.

DSC_0313-2

I stitched an extra line above the hanger (towards the folded side of each hanger), but underneath the pocket flaps, to reinforce extra support for the organizer.

Using a safety pin, I pinned the opened edge approximately where the top of the hanger was located on the opposite side. This way, the hanger can be removed easily when it comes time to wash it or put it away. The safety pin will act as a closing mechanism to hold the hanger in place.

 

DSC_0314-2DSC_0320-2

So there you have it, this is how I upcycled my over the door shoe organizer. Although, I technically only created smaller shoe organizers, I had the idea that I could use these smaller organizer to store smaller items such as jewelry, scarfs, socks, etc., that can get lost in a closet. Basically, anything you might store in the top drawer of your dresser, you might use this for. I don’t use a dresser, so this product can be useful for me. Right now I actually use a few of the pockets to keep some running and workout items organized. I like this design for the fact that it’s double sided and it can be folded up and put away if it’s not being used. Hopefully this post might spark some organizational ideas for your life.

Until next time!

DSC_0329

 

 

 

Zero Waste Week 2018

/ Yen-Van Tran / Leave a comment

08.12.2018

0600

ambassador-tree-trans

Zero Waste Week is almost here! This year we have more participants and the event is hoping to reach a larger audience. Rachelle Strauss is the creator and director behind Zero Waste Week, an annual awareness campaign since 2008. It takes place in the first full week in September each year, and promotes awareness in producing rash and the disposal of trash. Zero Waste Week encourages the public to be more aware of how much trash they produce as well has encouraging people and businesses to live and work more sustainable and reduce their carbon footprint. She has been featured in The Guardian, National Geographic and The Sun for her efforts in promoting awareness for a more sustainable future.

This is my second year participating in Zero Waste Week as an ambassador. I’m so grateful and proud to be a part of this movement. There are many others who are and have been a part of this movement long before I came along, you can meet them at Zero Waste Week Ambassadors. You can also read all about this week and get involved at Zero Waste Week- About.  Use the hashtag #ZeroWasteWeek to show us your progress! 

Each day has a theme of Zero Waste which focuses on different aspects of creating less waste. For Zero Waste Week 2018, I listed the topic for each day and I linked some of my blog posts that pertain to each topic

September 3, 2018, DAY 1

We will be discussing the difference between ‘necessary’ and unnecessary plastics. The amount of plastic polluting the ocean is astounding. By 2050,plastic in the oceans will outweigh fish, predicts a report from the Ellen MacArthur Foundation, in partnership with the World Economic Forum. Herare a few past blog posts which explain how and why I became very conscientious about my purchases. 

  1. Shopping At Thrift Stores
  2. 5 Questions to ask Before Purchasing
  3. My 30 Piece Capsule Wardrobe
  4. Zero Waste Shopping And Why

September 4, 2018, DAY 2

Auditing our daily personal care routine! Plastic containers in the bathroom are nothing new. However, because we use bathroom items so frequently, the amount of plastic containers we go through can be unnerving when you  look at the statistics. As the zero waste movement has caught on, more stores are offering bulk bathroom items and refill stations. If you want to read about some of my zero waste bathroom blog posts, check them out below. 

  1. A Zero Waste Bathroom
  2. Bulk Bathroom Shopping Kit
  3. DIY Simple Face Exfoliant And Facial Mask
  4. Bathroom Update
  5. Toilet Paper Is Not Zero Waste
  6. What I Stopped Buying- Bathroom Items

September 5, 2018, DAY 3

Plastics in the kitchen and food packaging seem to be a huge problem for those starting out on their zero waste journey. To make your kitchen zero waste, can be quite challenging.  Creating a zero waste kitchen took time and trial and error in my own experience. To read more about the challenges I faced, check out the blog posts below. 

  1. Bulk Grocery Shopping Kit
  2. Food And Bath Storage Containers
  3. Zero Waste Shopping And Why
  4. What I Stopped Buying- Kitchen Items
  5. How To Store Fruits And Vegetables Without Plastic Bags

September 6, 2018, DAY 4

Household cleaning seems to be a sensitive subject for many. There are a variety of sanitary concerns and medical concerns. As for me, I use a vinegar and water mix, baking soda and a bristle brush to clean. You can read more about my method in the link below. 

  1. Zero Waste Cleaning

September 7, 2018, DAY 5

Zero Waste is for life, not just a week! Plastic pollution, trash pollution, water and soil pollution is an ongoing battle. A zero waste lifestyle does require an awareness of oneself and decisions. There are parameters that some of us deal with, and that others don’t, such as medical conditions, personal health and financial constraints. As long as the effort and awareness of product consumption is considered on a day to day basis, reducing trash is inevitable. If you want to read about my moments and lessons throughout my zero waste journey, you can check out the links to my previous blog posts below. 

  1. A Zero Waste Lifestyle
  2. Seven Tips To Begin A Zero Waste Lifestyle
  3. Zero Waste And Minimalism
  4. Spreading the Zero Waste Word
  5. Sometimes You’ll Produce Trash

I hope you will want to take the pledge and reduce the amount of trash you consume, and if you want to read about my journey and how I got started, you can read that here in, How I Got Started. At the end of the week’s festivities, it’s time to take all you’ve learned during the week and start/continue your own plastic free journey. There are a lot of Pinterest boards, Facebook Groups and forums that offer tips to start a zero waste lifestyle or tips for different experiences with the zero waste lifestyle. You can check out my own social media boards and follow me, or you can follow the Zero waste Week community on Facebook, Twitter, Pinterest, and Instagram. 

What’s In My Purse?

/ Yen-Van Tran / 1 Comment

06.12.2018

0600

DSC_9989

Since I’ve written about What’s in My Makeup Bag? and What’s in My Sport Emergency Kit?, I thought I’d show you what I carry around in my purse too. These are the items I use daily and essentially, and these include my zero waste essentials.

So an overall view will reveal that I usually carry my water bottle, my eyeglasses case, purse, keys, sunglasses, my reusable utensils, my cloth napkin and my cloth handkerchief.

Sometimes I will switch out my water bottle with my tumbler, if I’m going to grab coffee. Most of the time I’ll usually carry my water bottle instead of my tumbler because water is more critical for me on a day to day basis.

In my purse, (which is a pencil bag, because pencil bags tend to have more pockets and are washable) I’ll carry my cards and cash, a small bottle of lotion, a comb, my business cards case, a barrette, extra hair ties, my lip balm, lipstick, eyeliner, my mini 3 in 1 stainless steel screwdriver key chain eyeglass repair tool, extra bobby pins (because you can never have enough), and a nail filer.

DSC_9999

The only perishable and wasteful items I carry on a daily basis is my lip balm and my lipstick. I refill my bottle of lotion from my bulk lotion bottles. Anyone who uses hair ties knows that they tend to break and I haven’t yet found a good alternative to tie up my hair. I might lean towards going back to the scrunchie though. With the extra protective fabric around the hair tie, the life of the hair tie can last longer.

So there you have it. My purse is simple, and I don’t carry extra stuff around to the point where I can’t find anything in my bag. I tend to divide my items into smaller bags so that they’re grouped together in a more organized fashion. These are my day to day essential items, what do you carry around in your bag?

Upcycling Milk Crates to a Shoe Rack

/ Yen-Van Tran / 1 Comment

02.06.2018

0600

Materials:

  • 2 Milk crates (about 12″ cubes)
  • Twelve 2″ Multi-Purpose Construction Screws
  • (Optional) Three 1″ wood screws – (for creating the holes)
  • 2 Wood boards (12″ x 11-1/4″ x 1/2″)
  • 16 small screws for holding seats in place
  • Pencil

Tools:

  • Power Screwdriver
  • Table saw / Mitre Saw (or saw it by hand with a rip hand saw)

So I needed a small bench shoe rack piece of furniture. All of the designs and products I flipped through on the internet weren’t quite what I had in mind. I needed a fairly short lengthed bench that didn’t need to store a lot of shoes. I also wanted a compact design. I only own six pairs of shoes and I don’t wear them all in the same season so the rest of the room would be for my family.

I knew I had a few milk crates, which I saw the potential use for this project. It was simple idea and I knew what I wanted the final product to look like.

The interior space within each milk crate was 12″ wide, 12″ high and 10-1/4″ deep. The height of the crate was enough room for two levels for shoe storage.

DSC_8825 - Copy

Since I was going to use two milk crates, I went ahead and found two random wood boards about 1/2″ thick. The boards I found were slightly wider than the depth of the crates, but I left the extra inch for larger shoes.

So using a miter saw, I cut each piece of wood board down to 12″ x 11-1/4″.

DSC_8834 - Copy

Next I divided the interior height in half and created a guideline down the middle. Since the crate is plastic, I used an exacto blade to lightly score the midline.

DSC_8837

Using the wood screws and my power screwdriver, I pinpointed the locations of where I wanted my 2″ screws to be located. I like using the wood screws when locating holes in plastic because I can hold the shank of the screw and still guide the power screwdriver to create the straight hole.

wood screw Diagram

DSC_8838

After the holes are created, I took the 2″ Multi-Purpose Construction Screws and screwed them into the premade holes.

DSC_8841DSC_8843

For the four screws that were located further towards the back of the box, I screwed the 2″ Multi-Purpose Construction Screws inwards. And for the two screws located towards the opening of the box, I screwed them outwards.

I wanted the back of the box to be supported more since it was further back. Also, I didn’t want anything sharp located towards the front opening.

DSC_8842 - Copy (2)

I simply install each box with a board, placing the boards on top of the screws. The boards fit well and were snug enough where they didn’t move either.

Most shoes are longer than 10-1/4″, so leaving the extra 1″ helps with different sized shoes. If you need to store boots or shoes that wouldn’t fit the original designed space, you can simply remove one of the boards and the two screws closest to the opening. (I left the two screws here to show the original design)

So there you have it, you can create a simple seat and shoe storage very quickly and with simple materials. You can install a wood board on top to create a bench or stack these crates on top of a 2″ x 4″ frame to have one more level. There’s a variety of designs this can break out into. I might just do that when the spring season rolls around.

Hope this post jogged up ideas!

DSC_8858 - Copy

DSC_8853 - Copy

Update:

I wanted to secure a seat on top of the crates so I took another extra piece of wood board and lined it next to the piece I usually keep on top of the creates.

DSC_9711

I took my pencil and traced the crate pattern on the underside of each board and then used small screws to outline at least two crate holes using the small screws. In order to know where I had to place my screws, I flipped my screws over so that they would be standing on their heads and then gauged where the sharp end of the screw would land. The head of the screws had to hug the insides of the traced corner, so I knew where to place it. Wherever the screw could touch both edges of the location, was where I knew I had to place the screw.

I measured the location for the screws in this manner because I wanted the screw to fit right inside of the hole I traced. The head of the screw as well as the thread of the screws had to fit comfortably into the existing holes, once it was flipped over.

DSC_9708

I didn’t screw the screws in the entire length of the thread, so be very aware of the depth of the wood piece you pick out and the screw length that you choose as well. The idea here was to still have the screws sticking out of the board so it would fit nicely into the holes that were traced.

DSC_9708DSC_9705

Once I placed the boards back onto the crates, the top was created into a quick seat to use while putting on shoes (or taking them off).

 

DSC_9721

So there you have it! I like this much more now with the seat on top, and secured into place.

 

Upcycling Denim Jeans

/ Yen-Van Tran / 5 Comments

01.30.2018

0600

Materials:

  • One pair of denim jeans

Tools:

  • Sewing machine
  • Sewing Kit

So recently I started going auditing my traveling items such as my bath bag, travel accessories as well as my sport bags. I wanted to find 3 pieces of clothing to donate, but I also noticed that my bath bag wasn’t containing my bath items comfortably.

So I had the choice to go buy/find a new bath bag or find another solution. Out of the items I decided to donate, I found a tank top, sweater and a pair of jeans. Denim is one of my favorite materials to work with. I love upcycling denim into new items. The idea of donating the pair of jeans wasn’t exactly what I thought I would do, so I decided to make a stand up bath bag for myself, or at least a few stand up bags.

I’ve owned bath bags before, but the material was with a polyester or nylon blend. Over time, my bath bags would have soap or toothpaste residue stains. I figured that with a denim bath bag, I could simply throw it into the washing machine and it would clean easily.

DSC_8685

I divided each leg in half by folding it in half. I then cut the legs off from the pair of jeans and then divided each piece in half.

DSC_8695

I turned each of them inside out and designated the wider end of the pieces as the bottom of the bag and the smaller ends as the top of the bag.  I folded the top of the bags down to create the drawstring tube. This is where I wanted to install the drawstring later.

DSC_8697 - Copy

I hemmed the bottoms of the bags by simply sewing a sew line across the bottom. I then sewed the drawstring tube. I measured 2″x2″ squares on the corners on bottom.

I marked these white dots on BOTH SIDES OF THE BAG, near the bottom section of the bag. These white dots will be used as guides of where you will sew in the next step.

DSC_8699 - Copy

I then flipped the bag upside down, and so that the right side seam was facing up. I then folded the bottom of the bag to create a diamond shape. You should be able to locate all four dots that were created in the last step, when molding the diamond shape.

DSC_8704 - Copy

The dots are guides to sew where you will sew horizontally across the diamond. After sewing the two lines, the diamond should look like this.

DSC_8712DSC_8718

Since I was initially thinking of making a new bath bag, I wanted to sew a small pocket inside of that bag. I had this extra pocket left over from my Handmade Handkerchiefs project, so I added it on the inside. To find the opposing edges of the box, you can locate it by finding the perpendicular lines of the top and bottom hemmed lines.

DSC_8715 - Copy

If you want to make a small pocket inside, you can sew a piece of material to the inside of the bag, as long as you leave to top of the material open.

In this case, because the pocket was more than half of the height of the bag, I placed the pocket towards the bottom of the bag. I also knew that I would be folding the bag down when in use, so placing it towards the bottom gave me room for the top to be folded down.

DSC_8719

Once I pulled the drawstrings through the bags, this is what they looked like. They stand up pretty well, and I can fold them down to create a top frame for the boxes.

DSC_8721

This is what my bath bag looks like now.

DSC_8795

I like the fact that I can simply fold my bag down and be able to access everything I need inside. I also have the habit of attaching a ring to the interior of any bag. So I attached a metal ring to the inside seam of the bag, because I wanted to hang small bath items for easy access.

So there you have it. This was my solution to my travel bath bag issue. I genuinely love denim and to make these stand up drawstring bags with this material is one of my favorite kinds of sewing projects that I like to get involved in.

I used my other bags for some camera gear and for another bag I use for traveling. The denim creates a nice thickness for the bottom of these bags, which is why I like to use them for electronics.

DSC_8794

As a bonus…

I made a bag out of the top part of my denim jeans. I simply flipped the top inside out and hemmed the pant leg openings.  Due to the nature of how the jeans were cut and sewed, I folded the outer edges of the jeans inward when I hemmed them.

DSC_9368DSC_9369

I then sewed a zipper to the top opening of the jeans using sewing pins to hold the zipper in place and then sewing it to my pants. I used the same sewing steps to attach the zipper as to when I  Created Slim Hanging Organizers.

DSC_9371

Since my zipper wasn’t quite long enough for the length of the jeans, I closed off the jeans by sewing the top together.

DSC_9372

DSC_9373

I used an extra tie to create the handles of this bag. This was a simple choice but some people may prefer to use a belt or something more to their taste. I chose the tie because I wanted to be able to throw everything into the washing machine.

DSC_9375DSC_9381

And as always, I attached a metal ring to my zipper for a slightly easier access.

I use this bag to hold some smaller items that need a bit of cushion like camera gear or smaller electronics.

DSC_9383

 

 

 

Creating Fabric Boxes

/ Yen-Van Tran / 8 Comments

01.16.2018

0600

Materials:

  • Hanging Fabric Shelf Organizer
  • Quilt Batting (optional)

Tools:

  • Sewing Machine or thread and needle
  • Sewing Kit
  • Ruler
  • Pencil
  • Iron and Ironing Mat

Hanging Fabric Shelf Organizer

So I had a hanging fabric shelf organizer which I had replaced by sewing slim hanging organizers from pillow cases. You can find that blog post at Created Slim Hanging Organizers. But once I replaced the canvas hanging organizer, I didn’t know what to do with it. So I decided to create small fabric boxes with the leftover material. I first took it apart, literally took it apart piece by piece. I recycled the cardboard and I was left with rectangular pieces of canvas.

This project works best if you have perfect square material, but I didn’t want to waste any material so my pieces were left as rectangular pieces. Rectangular canvas pieces yield rectangular shaped boxes. Square fabric pieces will result in perfect square boxes.

DSC_7915 - Copy

So I first worked on the larger fabric piece. I first sewed the edges of the fabric so it wouldn’t com apart. I wanted these boxes to have a rougher look to them so I didn’t hem the edges. You can insert a fitted quilt batting piece in between your fabric pieces if you are using a softer fabric and if you want your box sides to be a stiff frame. I didn’t use batting because my material is canvas in this project.

I folded it in half (doesn’t matter which direction), and then I marked off a 3 inch by 3 inch triangle on each corner of the folded side. These triangle marks are the red lines in the photo. The larger the triangle, the higher the height of the fabric box will stand.

 

DSC_7921-2

I opened it up and I folded the fabric piece in the perpendicular direction, with the first set of triangle marks still facing upwards.

DSC_7925

I then proceeded to fold the fabric and mark off the second set of 3 inch by 3 inch triangle on each corner of the folded side. These are located with the blue lines in the photo.

DSC_7929

From there, I sewed over the lines of where I had marked each set of triangles. I sewed the blue lines first. I then opened up the fabric piece, lined up the other corners in order to sew over the red lines.

DSC_7937DSC_7944

Once you sew all of the four corners, when you open the fabric, it should look something like this. However, now you have to flip the box inside-out. Once you do that, the rectangular tabs you created should be on the inside.

DSC_7945DSC_7948

With the four triangle flaps sticking straight up, fold them down to create a straight edge of the box. You can pin it down with sewing pins to watch the shape take form. Once you fold down all of the standing flaps, you should have a similar box like the photo below.

DSC_7952

Now you just need to sew the standing flaps down to create sharper straight edges of the box and then sew the flaps on the inside of the box to keep them flat against the sides.

DSC_7957

I’ve used the large fabric boxes to organize items in my linen closet as well as my camera gear items. Although these aren’t perfect squares, I like the idea that these fabric boxes are easily modified to most objects.

DSC_7960

For the smaller piece of fabric, I hemmed the edges to keep the fabric together and then I measured a 2 inch margin all around the edges. Here, you can insert a piece of fitted quilt batting before sewing the edges together, to give your fabric box a more framed look.

DSC_7962

I folded each edge over and ironed the lines to define the bottom of the box.

DSC_7963

Using sewing pins, I folded in each corner and held them there. These smaller triangles will help define the corners of the box.

DSC_7971

For each triangle corner, I found the center of the triangle and folded it in half. Once the triangle folded in half, the edges of the box came together naturally. I hand sewed these edges together by using a running stitch pattern. I sewed the running stitch in one direction, then simple went back the opposite direction to fill in the gaps in the pattern.

DSC_7975DSC_7978DSC_7980DSC_7982

Once I sewed all four corners, I proceeded to sew the triangle flaps on the inside of the box to the walls.

DSC_7987DSC_7988

I’ve used the smaller fabric boxes to keep smaller items organized that sit on shelves and table tops. So there you have it, these were very simple boxes made from the canvas material I had left over from the hanging fabric shelf organizer. You can use pretty much any fabric you want, but you may need to use quilt batting to strengthen the sides of the boxes.

DSC_7997

Upcycled Coat Rack From Spoons

/ Yen-Van Tran / 1 Comment

01.09.2018

0600

Materials:

  • Wood board (18 inches long x 5 inches wide 1-1/2 inches deep)
  • Four 3 inch wood screws
  • Ten 1-1/2 inch wood screws
  • 5 Spoons

Tools:

  • Power Drill
  • Power Screwdriver
  • Needle Nose Pliers
  • Slip Joint Pliers
  • Safety glasses
  • Gloves

DSC_8162DSC_8164

So I wanted to make a coat hanger but I didn’t want to buy one. Apparently I had materials at home to make one of my own. This project is a fairly easy DIY for any of you who are curious.

My board was 18 inches wide and I wanted a minimum of 1 inch on each side, for margins. This left me with 16″ to work with. So initially I wanted to use 7 spoons for the hangers, but after I measured the distance, I decided to only use 5 spoons.

DSC_8171-2

I divided the board up into three sections. The height of my board was 5-1/2″, but if you don’t want to use numbers, simply take a piece of paper and fold it into thirds. Then with a pencil, mark the first line and then the second. I wanted to offset my rows of spoons so the red line is for the top row of spoons and the green line is for the center of the bottom row of spoons.

Where the red line and margins intersect is where I drilled my top mounting holes. My bottom mounting holes is where the green line and the margins intersect. These holes are marked by the yellow circles in the image.

DSC_8179-2

For the spoons, I wanted to drill 2 holes to mount each spoon and I knew I had to create hooks by manipulating the spoons. I picked out a drill bit that was a similar size diameter of my screws I was going to use on the spoons. Usually I choose a drill bit smaller than my screw, but that working with wood only. When working with metal, you want a drill bit that the same size as the screw since metal won’t give. Also, if you don’t choose a drill bit smaller than your screw, there’s a good chance you’ll strip the screw’s threads as you drill.

The green line marks the point of where I wanted my spoons to bend upwards, so they could be used as hooks.

DSC_8173-2

When I drilled the holes, I wore gloves and my safety glasses because the metal slivers would fly off of the power drill. I applied slow but steady pressure while holding the spoon still and then I dumped the metal shavings into one side of my purple container. I did this to contain the shavings but also because it would be easier to discard them after I finished.

DSC_8184

I first started bending the spoons by using the edge of my step ladder, then I used my Slip Joint Pliers to hold the spoon while using the Needle Nose Pliers to bend the spoons into hooks.

DSC_8169

Once all of the spoons had holes drilled into them, I spaced the spons apart from each other in three inch increments. I proceed to attach the spoons to the board. For the wall mount attachment holes, I sunk the holes into the wood so that there was a slight design detail. I initial had made 2 drill holes so that I could mount it to the stud in the wall (those are the extra holes you see floating on the left half of  the board), but I changed my mind and decided to directly attach it to the drywall instead. Because I was planning to use three inch screws, I knew that mounting it to the drywall wouldn’t be a problem.

But because I changed my mind on which drill holes I wanted to use to mount the coat rack, I now had two random holes that looked out of place. To fix this, I mirrored the holes to the other side of the board and then filled in the extra holes will extra wood filler we had left over.

DSC_8185

I centered my coat rack and attached it to my wall. As you can see, the mistake holes look like design elements with the wood filler.

DSC_8198DSC_8200

So there it is, my coat rack made from spoons. These spoons are a few extra spare spoons from my mother’s kitchen and I really like that I was able to upcycle these extra spoons, knowing that a part of her kitchen was now used in an item I really needed. It’s a nice homage to my mom in a subtle way.

Our homes and possessions hold a great deal of different types of materials in which we can reuse and upcycle into new items.   Once you breakdown how different types of materials are used, the possibilities are endless. Scan your home and surroundings, I’m sure you’ll find a lot of resources.

 

 

Upcycling Fabric Shower Curtains

/ Yen-Van Tran / 2 Comments

12.05.2017

0600

Materials:

  • Two 72″ x 72″ Fabric Shower Curtains

Tools:

  • Sewing Machine
  • Sewing Kit

 

DSC_6896

Fabric Shower curtains are usually  made with polyester fabric. A few years ago, I had ordered extra fabric shower curtains and I really wanted to use up the material. I had previously posted a quick blog post about using fabric shower curtains as temporary screens for doors in Alternative Screen For Doors.

But now I wanted to see if I could upcycle the material again for another purpose.  This upcycling project works well if you have solid color curtains. I wanted to create a sheer curtain layer to hang with each of the three sets of my existing window curtains. I thought it would be interesting to upcycle my extra fabric shower curtains to sheer curtains for my windows. I still like the patterns I choose and with the sheer curtains up against my windows, the patterns would be illuminated as the sun hit them each morning.

So I took down each of my existing window curtains and measured them to see how much fabric I needed from the shower curtains. The width of the window wasn’t a problem since I had 72″ to work with. The only variable was the height of each curtain.

For my multicolored shower curtain, I divided the shower curtain in half length wise and width wise equally. I had planned to use the top half of this curtain to create my first sheer window curtain set. The bottom half would be combined with the top half of the bamboo curtain, to create the third set of window curtains.

InterDesign Vivo Botanical Fabric Shower Curtain-72x 72, Purple-Tan- LG - Copy

For my bamboo print shower curtain, I measured the height that I initially wanted starting from the bottom of the curtain. I did this because I wanted the second curtain set to be completely covered by the pattern. I left the white void at the top of the bamboo curtain because I knew I was going to use it in the third set of window curtains. I had planned to sew the top half of the bamboo shower curtains to the bottom half of the multicolored shower curtain to create the last set of sheer window curtains.

InterDesign Anzu Shower Curtain, Green- LG2 - Copy

I then pinned the edges that had been cut using sewing pins and hemmed them to clean up the trim around the shower curtain.

DSC_6889

Since the width of each shower curtain piece was wider than the individual window curtain pieces, I tucked and folded the shower curtain pieces to fit each window curtain width accordingly. I only sewed about 6″ up the shower curtain piece to hold the folded in piece in place, and across the bottom. You can sew the entire height of the folded piece, but I simple choose not to.

DSC_6893

DSC_6892

Since I know I want to keep these curtain designs as is, I decided to sew the new sheer curtain layer to my existing window curtains.  You don’t have to sew them, you can use safety pins as a temporary solution if you’re not sure about keeping the sheer layers, or if you want to change them out. Make sure you decide which side of the sheer curtain you want to face towards the window and which side of your existing window curtain you want to face inwards into your home. I personally don’t care about what my curtain looks like to the outside world so I have the nicer pattern facing inwards. This is why adding a sheer layer helps the presentation of my curtains to the outside world.

DSC_6891

To secure my curtains, I had initially made cord tiebacks with leftover material from an old bed sheet, in order to keep my curtains open. With the new sheer layer, I can tie back the solid color window curtain and leave the sheer layer or I can wrap them both back to let in even more sunlight.

 

Rollup Christmas Tree

/ Yen-Van Tran / Leave a comment

11.28.2017

0600

Materials:

  • 8 baseboards at 28″ long
  • 15 pieces of 12″ long thin twine rope
  • Extra: Matches to melt the ends of the twine together so it doesn’t come apart over time)

Tools:

  • Miter Saw
  • Drill & Drill Bits (Need 1/8″ drill bit for all holes)

DSC_7280 - Copy.JPG

  • Measure each base board at appropriate length
  • Organize each baseboard to it’s general location on the tree formation and mark the corners of where you plan to make the 45° cuts. I made my marks for my 45° cuts on the bottom edges of my baseboard pieces so my baseboard lengths would stay consistent.
  • Using a Miter Saw, take each baseboard and cut each end of each baseboard at 45°
  • Starting with the top of the tree, mark off each of the holes for each piece.

DSC_7315

DSC_7287 - Copy.JPG

DSC_7285 - Copy

DSC_7289

  • Drill each hole to create openings
  • Using the twine pieces, start tying the pieces together. To keep each space consistent, I tied the knots towards the end of the rope and the same amount of twine end to melt later.

DSC_7293

It’s a simple tree where the clean up is just rolling up the tree.  When I put up the Christmas lights, I simple wrap them around the edges of the pieces. I usually go in one direction so that the lines are more evenly spaced. Same as my blog post Minimalist Christmas Tree, I hang my ornaments off of the lights. For the more fragile ornaments, I hang them from paperclips and then hang them from the cord.

This was created as an option to not use push pins on the wall, but it was an interesting take on a holiday tree as well. Give it a try if you’re interested, and you can even change out the material I used too.

DSC_7347

DSC_7402DSC_7409DSC_7417

DSC_7488

Zero Waste Week 2017

/ Yen-Van Tran / 2 Comments

09.05.2017

0600

zero-waste-weekcampaign-13

Rachelle Strauss is the creator and director behind Zero Waste Week, an annual awareness campaign since 2008. It takes place in the first full week in September each year, and promotes awareness in producing rash and the disposal of trash. Zero Waste Week encourages the public to be more aware of how much trash they produce as well has encouraging people and businesses to live and work more sustainable and reduce their carbon footprint. She has been featured in The Guardian, National Geographic and The Sun for her efforts in promoting awareness for a more sustainable future.

This is my first year participating in Zero Waste Week as an ambassador. I’m so grateful to be a part of this movement. But there are many others who are and have been a part of this movement long before I came along, you can meet them at Zero Waste Week Ambassadors. You can also read all about this week and get involved at Zero Waste Week- About.

Each day has a theme of Zero Waste which focuses on different aspects of creating less waste. For Zero Waste Week 2017, I listed the topic for each day and I linked some of my blog posts that pertain to each topic:

  • Tuesday: Trashless Tuesday – Challenging participants to a Zero Waste day to see how little they can accumulate for landfill (considering asking people to carry their rubbish around in a see through bag for the day too!) Look for #trashlesstuesday on other social media sites to see how others utilize their trash.

To follow Zero Waste Week and Rachelle Strauss, here are links to her other social media:  Facebook, Twitter, Instagram and Pinterest.

Upcycling Shelves

/ Yen-Van Tran / 2 Comments

06.13.2017

0600

Materials:

Tools:

  • Miter saw
  • Electric drill  and drill bits

So my family usually keeps leftover material from previous house projects or from items that were disassembled. A lot of the time wood planks are left over. These vary in sizes so I try to upcycle them around the house. My father had a book shelf a while back and it had two 42″ shelves that were 1″ thick and two 72″ shelves that were one inch thick.

I  knew those shelves could be used elsewhere in the house so I designated the shorter shelves for the upstairs kitchenette and created shelves with the other two longer pieces, in two other separate areas of the house.

I bought four grey Everbilt 10 in. x 8 in. Gray Medium Duty Shelf Bracket for the kitchenette and I bought two white Everbilt 9.75 in. x 7.75 in. White Elegant Shelf Bracket for the shelf in the bedroom. The shelf in the hallway will be mounted up with two wood 2x4s on each side.

For the kitchenette, I located the studs by knocking on the wall (you can also use magnets to locate the nails located in the studs as well) and since I wanted the top shelf to have at least 16″ of space from the shelf to the ceiling, I had to create two marks that marked both the top and bottom of the top shelf. I then measured another 11″ below the bottom line of the top shelf and made two marks for the bottom shelf. I wanted to leave at least 22″ above the countertop so there was enough room for using the countertop surface.

Because the shorter shelves didn’t reach across the wall of the kitchenette, I offset the shelves to make the weight of the items on the wall even. I measured the distance between the studs for each shelf, and transferred that onto each shelf. It’s easier to attach the shelf brackets to the shelves first, and then attach them to the wall. My studs were 30″ (on center) between each, so I knew to leave half an inch from the edge of each shelf edge and then measure inwards 30″ to mark the next center of the next bracket.

Once I attached the brackets to the shelves, I had to pre-drill the holes for the screws in the studs on the wall. If you screw in the top screw on the bracket closest to the wall (where the blue arrow is pointing to), and then place a  small level on top (where the violet arrow is pointing), then you can swing the other bracket up (where the maroon arrow is pointing), until the level shows that the shelf is at an even plane.  This seemed to be the easiest way for me to attach the shelves and also double checking the correct balance of the shelves.

DSC_6193

 

DSC_5564

DSC_5571

For the shelf under the window, I first located where my studs were and made sure I cleared the electrical outlet. Ideally, I would have place a bracket where that electrical outlet is located, but there wasn’t any room. I wanted the height for this shelf to have an 8″ clearance, so I simply measured 8 inches below the existing shelf and marked two lines for the top and bottom of the shelf. For this shelf I trimmed the edges so it would fit the width of this space better. I also drilled a hole above where the outlet was located, so there would be access to the outlet.  I attached the brackets to the shelf based on the width of my studs. For this shelf, I literally held up the shelf with one hand, and traced the inside of the drill hole locations with the other. As long as I continued to press the shelf against the wall, it didn’t move much. I did this because I wanted to mark where the drill holes were and also to pinpoint the center of the holes. There wasn’t room to swing the shelf up to level it out, (such as the kitchenette example), so when I placed the level on the shelf, I only had to adjust the shelf slightly to even it out. Once the first screw was placed, it pretty much held up it’s own weight until I could drill in the last three screws.

DSC_5629

The shelf in the hallway was mounted with a different method. I actually had to cut this original shelf piece in half. It was the other 72″ long shelf piece, and by placing each of the halves next to one another, I created a  18-1/2″ depth shelf. I first located the studs in each wall and measured 11″ height clearance for the space above this shelf.  The width of the space was so small, that putting up brackets would have taken up too much room. I pre drilled the holes in the 2x4s based on the width of my studs I had located. Always remember which 2×4 belongs on which wall, so you’re not accidentally drilling extra holes. After that, I placed each piece on the new mount and held the shelf pieces in place with finishing nails.

DSC_5634

 

This was just one of my upcycling projects using materials I found in the garage. If you can find materials that are still in fairly good shape, I would try to upcycle it for a useful piece of item that you may need. It’s cheaper than going out to buy brand new material- especially since you’ll still have your extra supply of material laying around.  I like to use up what I buy, it’s habit of mine and it’s saved me money over the years. I hope this post helped jog some ideas for you!